Perle Systems 5500208-41 Configuring Users, Version, Add User, Delete User, Set Default User

Page 32

Configuring Users

escape

Defines the escape character. Returns you to the command line mode. This value is in hexadecimal with a default value of 1d (ASCII value GS).

Version

Description Displays firmware version and build.

User Level Normal, Admin

Syntax version

Configuring Users

Add User

Description	Adds a user. For units with 4 or less serial ports, you can configure up to 4 users. For
	units with 8 or more serial ports, the maximum number of users which can be added is
User Level	48. This is in addition to the admin user.
User Level	Admin
Syntax	add user <username>
Option	<username>
	The name of the user, without spaces. When you finish the command and press Enter,
	you will be prompted to enter and re-enter a password for the user.

Delete User

Description	Deletes a user.
User Level	Admin
Syntax	delete user <config_user>
Option	<config_user>
	You can see a list of users that can be deleted by typing delete user ?. You can not
	delete the admin user.

Set Default User

Description	Configures the Default User. When adding a new user, the profile of the default user
	will be used to assign the values of the various parameters of the new user. (CLI and
User Level	menu only).
User Level	Admin
Syntax	set default user [host-ip None<ip_address><config_host>]
	[hotkey-prefix <00-7f>] [idle-timer <0-4294967>]
	[language englishcustomlang]
	[level adminnormalrestrictedmenu]
	[line-access readinreadwrite [onoff]<line(s)> [0]]
	[port tcp-cleartelnet <tcp_port>]
	[service dsprompttelnettcp-clear] [sess-timer <0-4294967>]
Options	host-ip
	For outbound User Services such as Telnet, this is the target host name or IP address. If
	no IP address is specified, the Host IP value in the Default User configuration will be
	used. The default is 0.0.0.0. or None.

32	IOLAN DS1/TS2 CLI Reference Guide, Version 4.1

Image 32

Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands GlossaryIolan DS1/TS2 CLI Reference Guide, Version Intended Audience PrefaceAbout This Book Contacting Technical Support Making a Technical Support QueryRepair Procedure Feedback on this ManualContacting Technical Support Command Syntax IntroductionIntroduction CLI ConventionsCommand Shortcuts Command OptionsServer Commands Server CommandsSet Custom-App Set ServerBypass-password Dhcp/bootpOem-login Password-limitSet Service TimeoutPrompt-with-name Single-telnetHardware Commands Modbus Commands Set Modbus GatewayTruePort Baud Commands User Level AdminSet TruePort Remap-Baud Show TruePortShow IPv6 IPv6 CommandsSet IPv6 Add Custom-IPv6 Set Custom-IPv6Range Default 64 method manual Range DefaultDelete Custom-IPv6 Field Format IPv6 address prefix-bits manualIPv6 Commands User Commands Commands for Users Logged Into the IolanMenu PingResume ScreenSet User Set User SessionShow Line Users Syslog ConsoleShow Sessions Show TermtypeTelnet TcpportConfiguring Users Set Default UserVersion Add UserHotkey-prefix LevelLine-access ServiceSess-timer Phone-numberSet User Level Show Default User ConfigureduserShow the settings for the specified user Show the settings for the current userConfiguring Users Line Commands Port vs -Port Line CommandsLine Commands Set LineBreak-delay Dial-timeoutOptions break Break-lengthData-loggin InitialInitiate-connection Internet-addressReset Default Disabled Session stringsDefault 10 ms LockTerm1, Term2, Term3 user defined terminals User Stop-bitsTerm-type Set Line Interface Serverport Set Line ServiceConfighost Hostport Initstring Set ModemModemname Line Service Commands Show LineSet Telnet-Client Options termtypeSet UDP OutboundportStartipaddress EndipaddressSet Vmodem Set Vmodem-Phone IPaddress Set Modbus-Slave LineSet Modbus-Master Line Set Multihost Line Set Line Initiate-ConnectionShow Interface Show Telnet-ClientShow UDP Show VmodemModem Commands Add ModemDelete Modem Show ModemsPacket Forwarding Commands Set Packet-Forwarding LineEnable-end-trigger1 Enable-end-trigger2Enable-end-eof1 Enable-end-eof2Show Packet-Forwarding Line Packet Forwarding Commands Network Commands Chapter Snmp CommandsAdd Community Add TrapDelete Community Delete TrapSet Snmp Show SnmpTftp Commands Hosts CommandsGateway Commands Show HostsAdd Gateway Delete GatewayDescription Configures the gateway User Level Admin Syntax Set GatewayShow Gateways DestinationipShow Syslog Logging CommandsSet Syslog Time/Date Setting Commands Time CommandsTime Commands Show Date Administration Commands Bootup CommandsSet Bootup Show BootupConfiguration file Show ARPTftp File Transfer Commands NetloadHostname/ipaddress FilenameCustom Factory Default Options Factory-default-configNetsave Table or a DNS serverMotd Commands SetSet Motd Show MotdMotd Commands Statistic Commands Chapter Configuration StatisticsShow Netstat Show Modbus StatisticsRun-Time Statistics Set IO UDP O CommandsGlobal I/O Commands Set IO Temperature-Scale Set LineSet IO Failsafe Set IO ModbusSet IOChannel Mode Set IOChannelSet IOChannel Digital I/O Set IOChannel Digital InputSet IOChannel Digital Input Serial Pins Current status. The default is disabled Set IOChannel Digital OutputDescription can be up to 20 characters Will be displayed as activeActive-signal-width Inactive-signal-widthActive-to-inactive-delay Inactive-to-active-delaySet IOChannel Digital Output Serial Pins Set IOChannel RelayOptions description RelaynumberSet IOChannel Analog True Analog Options analogchannelTrigger-type Trigger-levelClear-mode Clear-levelSet IOChannel Analog Temperature Level Enabled Default Disabled keepaliveSet IOChannel IOExtension Options channelClient-initiated tcp-port Client-initiated multihostServer-initiated tcp-port Local-connection inputchannelSet IOChannel Multihost Show IOChannel StatusKill IOChannel ChannelShow IO Show IOChannelChannel Control Commands Digital OutputDigital Input RelayGlossary