Perle Systems 5500208-41 manual Set Line, Set IO Failsafe, Set IO Modbus, Set IO Temperature-Scale

Page 78

Set Line

Set IO Failsafe

Description	Sets the failsafe (watchdog) settings for I/O.
User Level	Admin
Syntax	set io failsafe [mode onoff] [timeout <seconds>]
Options	mode
	Enables/disables the Failsafe Timer. This is the global setting that must be enabled to
	set the Failsafe Action on the channel for digital outputs and relays. When this timer
	expires because of no I/O activity within the specified time interval, the Failsafe Action
	set for the channel determines the action on the output.
	timeout
	The number of seconds that must elapse with no I/O activity before the channel
	Failsafe Action is triggered. Valid values are 1-9999. The default is 30 seconds.

Set IO Modbus

Description	Enabling the Modbus option makes the IOLAN act as a Modbus Slave, allowing
User Level	Modbus Masters to communicate with the IOLAN to control and/or retrieve I/O data.
User Level	Admin
Syntax	set io modbus [mode onoff] [uid <1-255>]
Options	mode
	Enables/disables the ability to control/monitor I/O channels using the Modbus protocol.
	uid
	This is the UID you are assigning to the IOLAN, which is acting as a Modbus slave.

Set IO Temperature-Scale

Description	Sets the temperature scale that will be used for all Temperature input readings.
User Level	Admin
Syntax	set io temperature-scale celsiusfahrenheit
Option	temperature-scale
	Select the temperature scale that will be used to display temperature data, either
	Fahrenheit or Celsius. The default is Celsius.

Set Line

Set Line Service

Description Sets the Line Service settings to signal I/O. When the line service is set to signal-io, you also have the option of enabling the I/O extension for the serial singal pins. See Set IOChannel IOExtension on page 88 for more information.

User Level Admin

Syntax set line <number> service signal-io

Option signal-io

Sets the line to use signal I/O. You still need to define the serial pins for digital input (CTS, DSR, or DCD) or digital output (RTS or DTR). See Set IOChannel Digital Input (Serial Pins) on page 80 or Set IOChannel Digital Output (Serial Pins) on page 83 for configuration options.

78	IOLAN DS1/TS2 CLI Reference Guide, Version 4.1

Image 78

Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands GlossaryIolan DS1/TS2 CLI Reference Guide, Version Preface About This BookIntended Audience Contacting Technical Support Making a Technical Support QueryRepair Procedure Feedback on this ManualContacting Technical Support Introduction Command SyntaxIntroduction CLI ConventionsCommand Shortcuts Command OptionsSet Custom-App Server CommandsServer Commands Set ServerOem-login Bypass-passwordDhcp/bootp Password-limitPrompt-with-name Set ServiceTimeout Single-telnetHardware Commands Modbus Commands Set Modbus GatewaySet TruePort Remap-Baud TruePort Baud CommandsUser Level Admin Show TruePortIPv6 Commands Set IPv6Show IPv6 Add Custom-IPv6 Set Custom-IPv6Delete Custom-IPv6 Range Default 64 method manualRange Default Field Format IPv6 address prefix-bits manualIPv6 Commands User Commands Commands for Users Logged Into the IolanResume MenuPing ScreenSet User Set User SessionShow Sessions Show Line UsersSyslog Console Show TermtypeTelnet TcpportVersion Configuring UsersSet Default User Add UserHotkey-prefix LevelSess-timer Line-accessService Phone-numberSet User Level Show the settings for the specified user Show Default UserConfigureduser Show the settings for the current userConfiguring Users Line Commands Line CommandsPort vs -Port Line Commands Set LineOptions break Break-delayDial-timeout Break-lengthInitiate-connection Data-logginInitial Internet-addressDefault 10 ms ResetDefault Disabled Session strings LockStop-bits Term-typeTerm1, Term2, Term3 user defined terminals User Set Line Interface Set Line Service ConfighostServerport Hostport Set Modem ModemnameInitstring Line Service Commands Show LineSet Telnet-Client Options termtypeStartipaddress Set UDPOutboundport EndipaddressSet Vmodem Set Vmodem-Phone Set Modbus-Slave Line Set Modbus-Master LineIPaddress Set Multihost Line Set Line Initiate-ConnectionShow UDP Show InterfaceShow Telnet-Client Show VmodemDelete Modem Modem CommandsAdd Modem Show ModemsPacket Forwarding Commands Set Packet-Forwarding LineEnable-end-eof1 Enable-end-trigger1Enable-end-trigger2 Enable-end-eof2Show Packet-Forwarding Line Packet Forwarding Commands Add Community Network Commands ChapterSnmp Commands Add TrapSet Snmp Delete CommunityDelete Trap Show SnmpTftp Commands Hosts CommandsAdd Gateway Gateway CommandsShow Hosts Delete GatewayShow Gateways Description Configures the gateway User Level Admin SyntaxSet Gateway DestinationipLogging Commands Set SyslogShow Syslog Time Commands Time CommandsTime/Date Setting Commands Show Date Administration Commands Bootup CommandsConfiguration file Set BootupShow Bootup Show ARPHostname/ipaddress Tftp File Transfer CommandsNetload FilenameNetsave Custom Factory DefaultOptions Factory-default-config Table or a DNS serverSet Motd Motd CommandsSet Show MotdMotd Commands Show Netstat Statistic Commands ChapterConfiguration Statistics Show Modbus StatisticsRun-Time Statistics O Commands Global I/O CommandsSet IO UDP Set IO Failsafe Set IO Temperature-ScaleSet Line Set IO ModbusSet IOChannel Digital I/O Set IOChannel ModeSet IOChannel Set IOChannel Digital InputSet IOChannel Digital Input Serial Pins Description can be up to 20 characters Current status. The default is disabledSet IOChannel Digital Output Will be displayed as activeActive-to-inactive-delay Active-signal-widthInactive-signal-width Inactive-to-active-delayOptions description Set IOChannel Digital Output Serial PinsSet IOChannel Relay RelaynumberSet IOChannel Analog True Analog Options analogchannelClear-mode Trigger-typeTrigger-level Clear-levelSet IOChannel Analog Temperature Level Set IOChannel IOExtension EnabledDefault Disabled keepalive Options channelServer-initiated tcp-port Client-initiated tcp-portClient-initiated multihost Local-connection inputchannelKill IOChannel Set IOChannel MultihostShow IOChannel Status ChannelShow IO Show IOChannelDigital Input Channel Control CommandsDigital Output RelayGlossary