Perle Systems 5500208-41 Options break, Break-length, Break-delay, Connection-method, Data-bits

Page 40

Line Commands

Options break

Specifies how a break is interpreted:

zoff—The IOLAN ignores the break key completely and it is not passed through to the host. This is the default setting.

zlocal—The IOLAN deals with the break locally. If the user is in a session, the break key has the same effect as a hot key.

zremote—When the break key is pressed, the IOLAN translates this into a telnet break signal which it sends to the host machine.

zbreak-interrupt—On some systems such as SunOS, XENIX, and AIX, a break received from the peripheral is not passed to the client properly. If the client wishes to make the break act like an interrupt key (for example, when the stty options

-ignbrk and brkintr are set).

break-length

The length of time (in milliseconds) for which the break signal will be asserted on the se- rial port. Valid values are 0-65535.

Default is 1000 ms

A value of 0 will cause the "request to send a break signal" to be ignored.

break-delay

The length of time (in milliseconds) to delay after a break signal is sent before the IOLAN sends data. Valid values are 0-65535.

Default: 0 ms ( no delay )

connection-method

Determines how a modem will work on the line. Select from the following options:

zDirect Connect—Indicates that there is not a modem on the line. This is the default.

zDial In—Specify this option when a user is remote and will be dialing in via modem or ISDN TA.

zDial Out—Specify this option when a modem is attached to the serial port and is being used to dial out.

zDial In/Out—Specify this option when the IOLAN is being used as a router (depending on which end of the link your IOLAN is situated and how you want to initiate the communication).

data-bits

Specifies the number of bits in a byte. The default is 8.

dial-timeout

The number of seconds the IOLAN will wait to establish a connection to a remote modem. The default value is 45 seconds.

dial-retries

The number of times the IOLAN will attempt to establish a connection with a remote modem. The default value is 2.

flowin

Determines if input flow control is to be used. Default is On. This is active only when

Line Flow Control is set to Soft, Hard, or Both.

flowout

Determines if output flow control is to be used. Default is On. This is active only when

Line Flow Control is set to Soft, Hard, or Both.

40

IOLAN DS1/TS2 CLI Reference Guide, Version 4.1

Image 40
Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands GlossaryIolan DS1/TS2 CLI Reference Guide, Version About This Book PrefaceIntended Audience Contacting Technical Support Making a Technical Support QueryRepair Procedure Feedback on this ManualContacting Technical Support Command Syntax IntroductionIntroduction CLI ConventionsCommand Shortcuts Command OptionsServer Commands Server CommandsSet Custom-App Set ServerBypass-password Dhcp/bootpOem-login Password-limitSet Service TimeoutPrompt-with-name Single-telnetHardware Commands Modbus Commands Set Modbus GatewayTruePort Baud Commands User Level AdminSet TruePort Remap-Baud Show TruePortSet IPv6 IPv6 CommandsShow IPv6 Add Custom-IPv6 Set Custom-IPv6Range Default 64 method manual Range DefaultDelete Custom-IPv6 Field Format IPv6 address prefix-bits manualIPv6 Commands User Commands Commands for Users Logged Into the IolanMenu PingResume ScreenSet User Set User SessionShow Line Users Syslog ConsoleShow Sessions Show TermtypeTelnet TcpportConfiguring Users Set Default UserVersion Add UserHotkey-prefix LevelLine-access ServiceSess-timer Phone-numberSet User Level Show Default User ConfigureduserShow the settings for the specified user Show the settings for the current userConfiguring Users Line Commands Port vs -Port Line CommandsLine Commands Set LineBreak-delay Dial-timeoutOptions break Break-lengthData-loggin InitialInitiate-connection Internet-addressReset Default Disabled Session stringsDefault 10 ms LockTerm-type Stop-bitsTerm1, Term2, Term3 user defined terminals User Set Line Interface Confighost Set Line ServiceServerport Hostport Modemname Set ModemInitstring Line Service Commands Show LineSet Telnet-Client Options termtypeSet UDP OutboundportStartipaddress EndipaddressSet Vmodem Set Vmodem-Phone Set Modbus-Master Line Set Modbus-Slave LineIPaddress Set Multihost Line Set Line Initiate-ConnectionShow Interface Show Telnet-ClientShow UDP Show VmodemModem Commands Add ModemDelete Modem Show ModemsPacket Forwarding Commands Set Packet-Forwarding LineEnable-end-trigger1 Enable-end-trigger2Enable-end-eof1 Enable-end-eof2Show Packet-Forwarding Line Packet Forwarding Commands Network Commands Chapter Snmp CommandsAdd Community Add TrapDelete Community Delete TrapSet Snmp Show SnmpTftp Commands Hosts CommandsGateway Commands Show HostsAdd Gateway Delete GatewayDescription Configures the gateway User Level Admin Syntax Set GatewayShow Gateways DestinationipSet Syslog Logging CommandsShow Syslog Time Commands Time CommandsTime/Date Setting Commands Show Date Administration Commands Bootup CommandsSet Bootup Show BootupConfiguration file Show ARPTftp File Transfer Commands NetloadHostname/ipaddress FilenameCustom Factory Default Options Factory-default-configNetsave Table or a DNS serverMotd Commands SetSet Motd Show MotdMotd Commands Statistic Commands Chapter Configuration StatisticsShow Netstat Show Modbus StatisticsRun-Time Statistics Global I/O Commands O CommandsSet IO UDP Set IO Temperature-Scale Set LineSet IO Failsafe Set IO ModbusSet IOChannel Mode Set IOChannelSet IOChannel Digital I/O Set IOChannel Digital InputSet IOChannel Digital Input Serial Pins Current status. The default is disabled Set IOChannel Digital OutputDescription can be up to 20 characters Will be displayed as activeActive-signal-width Inactive-signal-widthActive-to-inactive-delay Inactive-to-active-delaySet IOChannel Digital Output Serial Pins Set IOChannel RelayOptions description RelaynumberSet IOChannel Analog True Analog Options analogchannelTrigger-type Trigger-levelClear-mode Clear-levelSet IOChannel Analog Temperature Level Enabled Default Disabled keepaliveSet IOChannel IOExtension Options channelClient-initiated tcp-port Client-initiated multihostServer-initiated tcp-port Local-connection inputchannelSet IOChannel Multihost Show IOChannel StatusKill IOChannel ChannelShow IO Show IOChannelChannel Control Commands Digital OutputDigital Input RelayGlossary