Perle Systems 5500208-41 manual Set UDP, Outboundport, Startipaddress, Endipaddress

Page 50

Line Service Commands

Set UDP

Description

Configures the UDP settings for the serial line.

User Level

Normal, Admin

Syntax

set udp line .<number>* entry 1234

 

both auto-learnspecific <UDP_port> [<start_IP_address>]

 

[<end_IP_address>]

 

set udp line .<number>* entry 1234 in

 

any-portauto-learnspecific <UDP_port> [<start_IP_address>]

 

[<end_IP_address>]

 

set udp line .<number>* entry 1234 out <UDP_port>

 

[<start_IP_address>] [<end_IP_address>]

 

set udp line .<number>* entry 1234 none

Options

entry 1234

 

Selects which of the 4 available entries we wish to define/modify. For each entry the

 

user can specify a different IP address range, UDP port and direction of data flow.

 

bothinoutnone

The direction in which information is received or relayed:

zNone—UDP service not enabled.

zIn—LAN to serial.

zOut—Serial to LAN.

zBoth—Messages are relayed both directions.

auto-learn

The IOLAN will only listen to the first port that it receives a UDP packet from.

Applicable when set to In or Both.

any-port

The IOLAN will receive messages from any port sending UDP packets. Applicable when set to In.

specific

The port that the IOLAN will use to relay messages to servers/hosts or the port from which the IOLANN will receive messages to be forwarded to the serial port. This option works with any setting except None. The IOLAN will listen for UDP packets on the port configured by the DS Port parameter.

<outbound_port>

The port that the IOLAN will use to relay messages to servers/hosts. The IOLAN will listen for UDP packets on the port configured by the DS Port parameter.

<start_ip_address>

The first host IP address in the range of IP addresses (for IPV4 or IPV6) that the

IOLAN will listen for messages from and/or send messages to.

<end_ip_address>

The last host IP address in the range of IP addresses (for IPV4, not required for IPV6) that the IOLAN will listen for messages from and/or send messages to.

50

IOLAN DS1/TS2 CLI Reference Guide, Version 4.1

Image 50
Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Channel Control Commands GlossaryIolan DS1/TS2 CLI Reference Guide, Version Intended Audience PrefaceAbout This Book Contacting Technical Support Making a Technical Support QueryRepair Procedure Feedback on this ManualContacting Technical Support Introduction Command SyntaxIntroduction CLI ConventionsCommand Shortcuts Command OptionsSet Custom-App Server CommandsServer Commands Set ServerOem-login Bypass-passwordDhcp/bootp Password-limitPrompt-with-name Set ServiceTimeout Single-telnetHardware Commands Modbus Commands Set Modbus GatewaySet TruePort Remap-Baud TruePort Baud CommandsUser Level Admin Show TruePortShow IPv6 IPv6 CommandsSet IPv6 Add Custom-IPv6 Set Custom-IPv6Delete Custom-IPv6 Range Default 64 method manualRange Default Field Format IPv6 address prefix-bits manualIPv6 Commands User Commands Commands for Users Logged Into the IolanResume MenuPing ScreenSet User Set User SessionShow Sessions Show Line UsersSyslog Console Show TermtypeTelnet TcpportVersion Configuring UsersSet Default User Add UserHotkey-prefix LevelSess-timer Line-accessService Phone-numberSet User Level Show the settings for the specified user Show Default UserConfigureduser Show the settings for the current userConfiguring Users Line Commands Line CommandsPort vs -Port Line Commands Set LineOptions break Break-delayDial-timeout Break-lengthInitiate-connection Data-logginInitial Internet-addressDefault 10 ms ResetDefault Disabled Session strings LockTerm1, Term2, Term3 user defined terminals User Stop-bitsTerm-type Set Line Interface Serverport Set Line ServiceConfighost Hostport Initstring Set ModemModemname Line Service Commands Show LineSet Telnet-Client Options termtypeStartipaddress Set UDPOutboundport EndipaddressSet Vmodem Set Vmodem-Phone IPaddress Set Modbus-Slave LineSet Modbus-Master Line Set Multihost Line Set Line Initiate-ConnectionShow UDP Show InterfaceShow Telnet-Client Show VmodemDelete Modem Modem CommandsAdd Modem Show ModemsPacket Forwarding Commands Set Packet-Forwarding LineEnable-end-eof1 Enable-end-trigger1Enable-end-trigger2 Enable-end-eof2Show Packet-Forwarding Line Packet Forwarding Commands Add Community Network Commands ChapterSnmp Commands Add TrapSet Snmp Delete CommunityDelete Trap Show SnmpTftp Commands Hosts CommandsAdd Gateway Gateway CommandsShow Hosts Delete GatewayShow Gateways Description Configures the gateway User Level Admin SyntaxSet Gateway DestinationipShow Syslog Logging CommandsSet Syslog Time/Date Setting Commands Time CommandsTime Commands Show Date Administration Commands Bootup CommandsConfiguration file Set BootupShow Bootup Show ARPHostname/ipaddress Tftp File Transfer CommandsNetload FilenameNetsave Custom Factory DefaultOptions Factory-default-config Table or a DNS serverSet Motd Motd CommandsSet Show MotdMotd Commands Show Netstat Statistic Commands ChapterConfiguration Statistics Show Modbus StatisticsRun-Time Statistics Set IO UDP O CommandsGlobal I/O Commands Set IO Failsafe Set IO Temperature-ScaleSet Line Set IO ModbusSet IOChannel Digital I/O Set IOChannel ModeSet IOChannel Set IOChannel Digital InputSet IOChannel Digital Input Serial Pins Description can be up to 20 characters Current status. The default is disabledSet IOChannel Digital Output Will be displayed as activeActive-to-inactive-delay Active-signal-widthInactive-signal-width Inactive-to-active-delayOptions description Set IOChannel Digital Output Serial PinsSet IOChannel Relay RelaynumberSet IOChannel Analog True Analog Options analogchannelClear-mode Trigger-typeTrigger-level Clear-levelSet IOChannel Analog Temperature Level Set IOChannel IOExtension EnabledDefault Disabled keepalive Options channelServer-initiated tcp-port Client-initiated tcp-portClient-initiated multihost Local-connection inputchannelKill IOChannel Set IOChannel MultihostShow IOChannel Status ChannelShow IO Show IOChannelDigital Input Channel Control CommandsDigital Output RelayGlossary