Perle Systems 5500208-41 manual Set User

Page 35

Configuring Users

Set User

Description Sets users settings. Normal-level users can configure only their own settings. Admin-level users can configure any users settings, including their own (with the exception of their User Level, which must stay at Admin).

User Level Normal, Admin

Syntax set user . [hotkey-prefix <00-7f>] [language englishcustomlang] [password]

Admin set user .<username>*

[host-ip None<ip_address><config_host>] [hotkey-prefix <00-7f>] [idle-timer <0-4294967>] [language englishcustomlang]

[level adminnormalrestrictedmenu] [password] [line-access readinreadwrite [onoff]<line(s)> [0]] [service dsprompttelnettcp-clear] [sess-timer <0-4294967>] [port tcp-cleartelnet <tcp_port>]

Options host-ip

For outbound User Services such as Telnet, this is the target host name or IP address. If no IP address is specified, the Host IP value in the Default User configuration will be used. The default is 0.0.0.0. or None.

hotkey-prefix

The prefix that a user types to control the current session. The default value is hex 01, which corresponds to Ctrl-a(^a) (hex value 02 would be Ctrl-b (^b), etc.):

z^a number—To switch from one session to another, press ^a and then the required session number. For example, ^a 2 would switch you to session 2. Pressing ^a 0 will return you to the IOLAN Menu.

z^a n—Display the next session. The current session will remain active. The lowest numbered active session will be displayed.

z^a p—Display the previous session. The current session will remain active. The highest numbered active session will be displayed.

z^a m—To exit a session and return to the IOLAN. You will be returned to where you left off. The session will be left running.

z^a l—(Lowercase L) Locks the line until the user unlocks it. The user is prompted for a password (any password, excluding spaces) and locks the line. Next, the user must retype the password to unlock the line.

z^r—When you switch from a session back to the Menu, the screen may not be redrawn correctly. If this happens, use this command to redraw it properly. This is always Ctrl R, regardless of the Hotkey Prefix.

The User Hotkey Prefix value overrides the Line Hotkey Prefix value. You can use the

Hotkey Prefix keys to lock a line only when the line Lock parameter is On.

idle-timer

The amount of time, in seconds, that the Idle Timer will run. Use this timer to close a connection because of inactivity. When the Idle Timer expires, because there has been no exchange of data within the specified time, the IOLAN will close the connection.

The default value is 0 (zero), meaning that the Idle Timer will not expire (the connection is open permanently). The maximum value is 4294967 seconds. The User Idle Timer will override the Line Idle Timer, with the exception of reverse Telnet sessions.

language

You can specify whether a user will use English or Customlang as the language that appears in the Menu or CLI. The IOLAN supports one custom language that must be downloaded to the IOLAN; otherwise, Customlang defaults to English.

35

Image 35
Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents User Commands Line Commands Network Commands Time Commands Statistic Commands Glossary Channel Control CommandsIolan DS1/TS2 CLI Reference Guide, Version Intended Audience PrefaceAbout This Book Making a Technical Support Query Contacting Technical SupportFeedback on this Manual Repair ProcedureContacting Technical Support CLI Conventions Command SyntaxIntroduction IntroductionCommand Options Command ShortcutsSet Server Server CommandsServer Commands Set Custom-AppPassword-limit Bypass-passwordDhcp/bootp Oem-loginSingle-telnet Set ServiceTimeout Prompt-with-nameHardware Commands Set Modbus Gateway Modbus CommandsShow TruePort TruePort Baud CommandsUser Level Admin Set TruePort Remap-BaudShow IPv6 IPv6 CommandsSet IPv6 Set Custom-IPv6 Add Custom-IPv6Field Format IPv6 address prefix-bits manual Range Default 64 method manualRange Default Delete Custom-IPv6IPv6 Commands Commands for Users Logged Into the Iolan User CommandsScreen MenuPing ResumeSet User Session Set UserShow Termtype Show Line UsersSyslog Console Show SessionsTcpport TelnetAdd User Configuring UsersSet Default User VersionLevel Hotkey-prefixPhone-number Line-accessService Sess-timerSet User Level Show the settings for the current user Show Default UserConfigureduser Show the settings for the specified userConfiguring Users Set Line Line CommandsPort vs -Port Line Commands Line CommandsBreak-length Break-delayDial-timeout Options breakInternet-address Data-logginInitial Initiate-connectionLock ResetDefault Disabled Session strings Default 10 msTerm1, Term2, Term3 user defined terminals User Stop-bitsTerm-type Set Line Interface Serverport Set Line ServiceConfighost Hostport Initstring Set ModemModemname Show Line Line Service CommandsOptions termtype Set Telnet-ClientEndipaddress Set UDPOutboundport StartipaddressSet Vmodem Set Vmodem-Phone IPaddress Set Modbus-Slave LineSet Modbus-Master Line Set Line Initiate-Connection Set Multihost LineShow Vmodem Show InterfaceShow Telnet-Client Show UDPShow Modems Modem CommandsAdd Modem Delete ModemSet Packet-Forwarding Line Packet Forwarding CommandsEnable-end-eof2 Enable-end-trigger1Enable-end-trigger2 Enable-end-eof1Show Packet-Forwarding Line Packet Forwarding Commands Add Trap Network Commands ChapterSnmp Commands Add CommunityShow Snmp Delete CommunityDelete Trap Set SnmpHosts Commands Tftp CommandsDelete Gateway Gateway CommandsShow Hosts Add GatewayDestinationip Description Configures the gateway User Level Admin SyntaxSet Gateway Show GatewaysShow Syslog Logging CommandsSet Syslog Time/Date Setting Commands Time CommandsTime Commands Show Date Bootup Commands Administration CommandsShow ARP Set BootupShow Bootup Configuration fileFilename Tftp File Transfer CommandsNetload Hostname/ipaddressTable or a DNS server Custom Factory DefaultOptions Factory-default-config NetsaveShow Motd Motd CommandsSet Set MotdMotd Commands Show Modbus Statistics Statistic Commands ChapterConfiguration Statistics Show NetstatRun-Time Statistics Set IO UDP O CommandsGlobal I/O Commands Set IO Modbus Set IO Temperature-ScaleSet Line Set IO FailsafeSet IOChannel Digital Input Set IOChannel ModeSet IOChannel Set IOChannel Digital I/OSet IOChannel Digital Input Serial Pins Will be displayed as active Current status. The default is disabledSet IOChannel Digital Output Description can be up to 20 charactersInactive-to-active-delay Active-signal-widthInactive-signal-width Active-to-inactive-delayRelaynumber Set IOChannel Digital Output Serial PinsSet IOChannel Relay Options descriptionOptions analogchannel Set IOChannel Analog True AnalogClear-level Trigger-typeTrigger-level Clear-modeSet IOChannel Analog Temperature Level Options channel EnabledDefault Disabled keepalive Set IOChannel IOExtensionLocal-connection inputchannel Client-initiated tcp-portClient-initiated multihost Server-initiated tcp-portChannel Set IOChannel MultihostShow IOChannel Status Kill IOChannelShow IOChannel Show IORelay Channel Control CommandsDigital Output Digital InputGlossary