Omnitron Systems Technology 2FXM2 user manual Port Access

Page 27

4.3.1Port Access

The Port Access option allows the ports to be disabled/enabled while maintaining the port configuration and network link

To configure Port Access, select option 11 for the Port 1 and option 12 for the Port 2 from the Port configuration screen.

4.3.2Bandwidth Control

The 2FXM2 Bandwidth Control is accessed by selecting option 8 at the Port configuration screen. The 2FXM2 provides separate ingress and egress rate control on each port.

Ingress rates are limited by Committed Information Rate (CIR) and Committed Burst Size (CBS). The committed information rate (CIR) is the rate at which the network supports data transfer under normal operations. The committed burst size (CBS) defines the number of bits that can transmit over a specified time interval when congestion is occurring. Ingress CIR values are entered as a number of kbps, ranging from 64kbps to 100,000kbps. CIR values will be rounded to the nearest 64k. CBS values can range from 5kB to 150kB.

Ingress rate limiting provides an excess traffic policy with the option to “drop” the excess frames or “accept, send PAUSE” to the port’s link partner when traffic excess the ingress CIR and CBS values.

Egress rate are selected from a menu of 20 options.

Egress rate limiting can be selected to use either Starvation Queuing (low latency) or Weighted Fair Queuing (high latency). Starvation Queuing processes all high priority traffic before any low priority traffic and uses a strict priority scheme. Weighted Fair Queuing will process high priority traffic more often then low priority traffic in an 8 (high priority), 4, 2, 1 (low priority) weighted scheme.

PI

SA

Bandwidth Control - iConverter 2FXM2

iConverter Serial Agent

Identifier -

 

 

 

Chassis Number

= 1

 

 

Slot Number

= 1

 

 

Model Number

= 8959N-0

 

Port 1

Control

 

 

--------------------------------------

 

1: Ingress CIR

 

100000 kbps

 

2: Ingress CBS

 

150 kB

 

3: Excess Traffic Policy

Drop

 

4: Egress rate

 

100 Mbps

 

5: Queueing

 

Fair Weight

 

Port 2

Control

 

 

--------------------------------------

 

6: Ingress CIR

 

100000 kbps

 

7: Ingress CBS

 

150 kB

 

8: Excess Traffic Policy

Drop

 

9: Egress rate

 

100 Mbps

 

10: Queueing

 

Fair Weight

 

Enter Choice, Previous Screen(0), (H)elp, E(x)it >

Page 27

Image 27
Contents Standalone and PLUG-IN Module Table of Contents Plug-In OverviewPort Structure B B B B B B B Installation ProcedureThese DIP-switches are for factory use only 1.5 SW5 Fiber Port 2 Full/Half Duplex FDX/HDX DIP-switch Bank 2 is only available on the plug-in module Installing PLUG-IN Modules and Connecting Cables Passwords Management Options screen will be displayed 2FXM2 Setting the Chassis Number and Name Setting 2FXM2 Passwords Setting Snmp Preferences Setting SNMPv1/v2c Read and Write Community Names Setting the Snmp Trap IP Host Addresses Enabling/Disabling Soft-switch Reload Access the 2FXM2 Remotely Updating the 2FXM2 Firmware via the Serial Console Port Verify Operation NMM Detailed Module Configuration2FXM2 LED Module Management Mode Port Configuration Port Access To change the ingress rate of the Port 1, select option SFP Information 5 802.3ah Parameters Local Status Section OUI 6 802.3ah Events Port Vlan Off Tagged Vlan Pvid BP BVlan ID VID BP a BP BVlan Table is Empty Vlan ID +1 Vlan ID CNode Loopback To refresh the Port Statistic screen, press Enter Cable Types 2FXM2 SpecificationsPossible Causes Troubleshooting GuideLimitation of Warranty Warranty