Multi-Tech Systems MT4X56USB manual Windows 95/98 Configuration Utility

Page 34

MultiModemUSB User Guide

Windows 95/98 Configuration Utility

The Windows 95 and Windows 98 Configuration utilities are located in your Windows System directory. These utilities allow you to manage various resources of your MT4X56USB. You can:

check the version numbers and other information regarding the drivers,

uninstall the USB environment,

check mapping of each physical communications port to the Windows COM port numbers,

assign the physical ports to any available Windows COM port number from 1 to 255, and

give your MT4X56USB a user-friendly name (useful if you have more than one).

To access the Configuration utility:

1.Double-click the edgeport.exe file located in your Windows System directory.

2.The MultiModem Properties dialog box is displayed.

While in the General tab, use your cursor to highlight your MT4X56USB and then click the Information or the Configure button.

The Information screen (not shown) displays information about your MT4X56USB; including manufacturer’s name, device name, serial and part number, ROM size, CPU Revision, RAM size, etc.

The configuration screen (see below) allows you to change the device name and the starting number for the ports.

Click OK to save the changes and return to the MultiModemUSB USB Properties dialog box.

34

MT4X56USB

Image 34
Contents MultiModemUSB Model MT4X56USB User GuidePatents User GuideRecord of Revisions TrademarksContents Glossary of Terms Index Introduction and Description Introduction FeaturesMultiModemUSB User Guide Preview of this Guide Technical SpecificationsInstallation Introduction and DescriptionRelated Documentation Hub Front PanelModem Ports Ports 1, 2, 3, SystemUSB Type B Downstream Connector RJ-ll Modem ConnectorUSB Type a Upstream Connector Power ConnectorInstallation Safety Warning Telecom UnpackingInstallation Cabling your MT4X56USBMT4X56USB Software Loading and Configuration Loading your Driver Software System USB SupportMT4X56USB Drivers for Windows Software Loading and Configuration Uninstalling MultiModemUSB in Windows MT4X56USB Drivers for Windows Uninstalling MultiModemUSB in Windows MultiModemUSB Drivers Install dialog box displays Click Next MT4X56USB Drivers for Windows NTSelect Add/Remove Programs Uninstalling MultiModemUSB in Windows NTAdd/Remove MT4X56USB Drivers for Windows Click Finish Software Loading and Configuration Select Add/Remove Hardware Installing Your V.90 Modems Click Start Settings Control Panel ModemsRead Carefully Software Loading and Configuration MT4X56USB Installing Your V.90 Modems Windows Click Start Settings Control Panel Phone and Modems optionMT4X56USB Software Loading and Configuration Windows 95/98 Configuration Utility MT4X56USB Windows NT 4.0/2000 Configuration Utility MT4X56USB MT4X56USB AT Commands, S-Registers and Result Codes Repeat Last Command AT Command SummaryCommand Enter Key AnswerAT Commands, S-Registers and Result Codes Information Request Return Online to Data ModeResult Codes Enable/Disable Modulation HandshakeTone Dialing Modem ResetLoad Factory Settings Result Code FormatTest Commands Communications ModeAsynchronous Communications Mode Display Current SettingsCommand &Zy=x Store Dialing Command Store Current ConfigurationSelect Stored Configuration for Hard Reset \An Select Maximum MNP Block Size\Kn Break Control \Nn Error Correction Mode Selection\Tn Inactivity Timer \Qn Flow Control SelectionEnter Setup Password Command %DCn AT Command ControlCommand %En Fallback and Fall Forward Control Command #S=x Store Setup PasswordCommand +++ATCR Escape Sequence Command %%%ATCRRemote Configuration Escape SequenceRegister Unit Range Default Description RegistersS38 Upstream data ratesResult Codes Terse Verbose DescriptionFor more information on scripting, click the Help button Remote Configuration Setup Remote Configuration ProcedureChanging the Setup Password Remote Configuration and Management Remote Configuration CommandsChanging the Remote Escape Character MT4X56USB Troubleshooting Modem Does Not Respond to Commands None of the Indicators LightModem Dials But Cannot Connect Troubleshooting Modem Disconnects While OnlineModem Doesn’t Work with Caller ID Modem Cannot Connect When AnsweringLoopback Tests Fax and Data Software Can’t Run at the Same TimeTest procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Remote digital loopback testLocal Digital Loopback Test V.54 Loop Local digital loopback testInstalling Microsoft USB Support Windows 95/98 TroubleshootingDetermining Why USB Support Is Not Present Double-click the Universal Serial Bus Controller iconUpgrade Procedure Identify the Current Firmware Version Upgrade OverviewIdentify the MT4X56USB Firmware Multi-Tech Web SiteUpgrade Procedure Download the Upgrade FileExtract the Upgrade Files Clear Your Stored ParamentersUpgrade the Modem’s Firmware Restore Your ParametersService, Warranty and Tech Support Software User License Agreement Service, Warranty and Tech Support Limited WarrantyOn-line Warranty Registration Tech SupportService Contacting Tech Support via E-mailAppendices FCC Part Appendix a Regulatory InformationClass B Statement Industry CanadaFCC Part 68 Telecom AppendicesFAX Branding Statement Canadian Limitations NoticeNew Zealand Telecom Warning Notice EMC, Safety and Terminal Directive ComplianceCommission Decision CTR21 International Modem RestrictionsAppendix B V.90 Support TroubleshootingIntroduction Glossary of Terms MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Index IndexConfiguration MT4X56USB Software user license agreement Speed