Multi-Tech Systems MT4X56USB manual

Page 80

MultiModemUSB User Guide

A

Analog signal: A waveform which has amplitude, frequency and phase, and which takes on a range of values between its maximum and minimum points.

Analog Transmission: One of two types of telecommunications which uses an analog signal as a carrier of voice, data, video, etc. An analog signal becomes a carrier when it is modulated by altering its phase, amplitude and frequency to correspond with the source signal. Compare with digital transmission.

Application Program Interface (API): A software module created to allow dissimilar, or incompatible applications programs to transfer information over a communications link. APIs may be simple or complex; they are commonly required to link PC applications with mainframe programs.

ASCII (American Standard Code for Information Interchange) (pronounced “askey”): A binary code for data that is used in communications and in many computers and terminals. The code is used to represent numbers, letters, punctuation and control characters. The basic ASCII code is a 7-bit character set which defines 128 possible characters. The extended ASCII file provides 255 characters.

Asynchronous Transfer Mode (ATM): A very high-speed method of transmission that uses fixed-size cells of 53 bytes to transfer information over fiber; also known as cell relay.

AT Commands: A standard set of commands used to configure various modem parameters, establish connections and disconnect. The “AT” is used to get the “attention” of the modem before the actual command is issued.

Availability: The measure of the time during which a circuit is ready for use; the complement of circuit “outage” (100% minus % outage = % available).

B

Babble: unexpected bus activity that persists beyond a specified point in a frame.

Backbone: 1. A set of nodes and their interconnecting links providing the primary data path across a network. 2. In a local area network multiple-bridge ring configuration, a high-speed link to which the rings are connected by means of bridges. A backbone may be configured as a bus or as a ring. 3. In a wide area network, a high-speed link to which nodes or data switching exchanges (DSEs) are connected. 4. A common distribution core that provides all electrical power, gases, chemicals, and other services to the sectors of an automated wafer processing system.

Background: An activity that takes place in the PC while you are running another application. In other words, the active user interface does not correspond to the ‘background’ task.

Bandwidth: the amount of data transmitted per unit of time, typically bits per second (bps) or bytes per second (Bps).

Bell Operating Companies (BOC): The family of corporations created during the divestiture of AT&T. BOCs are independent companies which service a specific region of the US. Also called Regional Bell Operating Companies (RBOCs).

Bell Pub 41450: The Bell publication defining requirements for data format conversion, line conditioning, and termination for direct DDS connection.

Bell Pub 62310: The Bell publication defining requirements for data format conversion, line conditioning, and termination for direct DDS connection.

Binary Synchronous Communication (BSC): A form of telecommunication line control that uses a standard set of transmission control characters and control character sequences, for binary synchronous transmission of binary-coded data between stations.

Bit (Binary digit): A bit is the basis of the binary number system. It can take the value of 1 or 0. Bits are generally recognized as the electrical charge generated or stored by a computer that represent some portion of usable information.

Bps (bits per second): A unit to measure the speed at which data bits can be transmitted or received. Bps differs from baud when more than one bit is represented by a single cycle of the carrier.

Bridges: 1. A functional unit that interconnects two local area networks that use the same logical link protocol but may use different medium access control protocols. 2. A functional unit that interconnects multiple LANs (locally or remotely) that use the same logical link control protocol but that can use different medium access control protocols. A bridge forwards a frame to another bridge based on the medium access control (MAC) address. 3. In the connection of local loops, channels, or rings, the equipment and techniques used to match circuits and to facilitate accurate data transmission.

Buffer: A temporary storage register or Random Access Memory (RAM) used in all aspects of data communications which prevents data from being lost due to differences in transmission speed. Keyboards, serial ports, muxes and printers are a few examples of the devices that contain buffers.

Bus: A common channel between hardware devices either internally between components in a computer, or externally between stations in a communications network.

80

MT4X56USB

Image 80
Contents MultiModemUSB Model MT4X56USB User GuideUser Guide Record of RevisionsPatents TrademarksContents Glossary of Terms Index Introduction and Description MultiModemUSB User Guide FeaturesIntroduction Technical Specifications InstallationPreview of this Guide Introduction and DescriptionRelated Documentation Front Panel Modem Ports Ports 1, 2, 3,Hub SystemRJ-ll Modem Connector USB Type a Upstream ConnectorUSB Type B Downstream Connector Power ConnectorInstallation Safety Warning Telecom UnpackingInstallation Cabling your MT4X56USBMT4X56USB Software Loading and Configuration MT4X56USB Drivers for Windows System USB SupportLoading your Driver Software Software Loading and Configuration Uninstalling MultiModemUSB in Windows MT4X56USB Drivers for Windows Uninstalling MultiModemUSB in Windows MultiModemUSB Drivers Install dialog box displays Click Next MT4X56USB Drivers for Windows NTAdd/Remove Uninstalling MultiModemUSB in Windows NTSelect Add/Remove Programs MT4X56USB Drivers for Windows Click Finish Software Loading and Configuration Select Add/Remove Hardware Installing Your V.90 Modems Click Start Settings Control Panel ModemsRead Carefully Software Loading and Configuration MT4X56USB Installing Your V.90 Modems Windows Click Start Settings Control Panel Phone and Modems optionMT4X56USB Software Loading and Configuration Windows 95/98 Configuration Utility MT4X56USB Windows NT 4.0/2000 Configuration Utility MT4X56USB MT4X56USB AT Commands, S-Registers and Result Codes AT Command Summary Command Enter KeyRepeat Last Command AnswerAT Commands, S-Registers and Result Codes Return Online to Data Mode Result Codes Enable/DisableInformation Request Modulation HandshakeModem Reset Load Factory SettingsTone Dialing Result Code FormatCommunications Mode Asynchronous Communications ModeTest Commands Display Current SettingsStore Current Configuration Select Stored Configuration for Hard ResetCommand &Zy=x Store Dialing Command \An Select Maximum MNP Block Size\Nn Error Correction Mode Selection \Tn Inactivity Timer\Kn Break Control \Qn Flow Control SelectionCommand %DCn AT Command Control Command %En Fallback and Fall Forward ControlEnter Setup Password Command #S=x Store Setup PasswordCommand +++ATCR Escape Sequence Command %%%ATCRRemote Configuration Escape SequenceRegister Unit Range Default Description RegistersS38 Upstream data ratesResult Codes Terse Verbose DescriptionFor more information on scripting, click the Help button Remote Configuration Changing the Setup Password Remote Configuration ProcedureSetup Changing the Remote Escape Character Remote Configuration CommandsRemote Configuration and Management MT4X56USB Troubleshooting Modem Dials But Cannot Connect None of the Indicators LightModem Does Not Respond to Commands Troubleshooting Modem Disconnects While OnlineModem Cannot Connect When Answering Loopback TestsModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeTest procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Remote digital loopback testLocal Digital Loopback Test V.54 Loop Local digital loopback testWindows 95/98 Troubleshooting Determining Why USB Support Is Not PresentInstalling Microsoft USB Support Double-click the Universal Serial Bus Controller iconUpgrade Procedure Upgrade Overview Identify the MT4X56USB FirmwareIdentify the Current Firmware Version Multi-Tech Web SiteDownload the Upgrade File Extract the Upgrade FilesUpgrade Procedure Clear Your Stored ParamentersUpgrade the Modem’s Firmware Restore Your ParametersService, Warranty and Tech Support Software User License Agreement Limited Warranty On-line Warranty RegistrationService, Warranty and Tech Support Tech SupportService Contacting Tech Support via E-mailAppendices Appendix a Regulatory Information Class B StatementFCC Part Industry CanadaFCC Part 68 Telecom AppendicesFAX Branding Statement Canadian Limitations NoticeEMC, Safety and Terminal Directive Compliance Commission Decision CTR21New Zealand Telecom Warning Notice International Modem RestrictionsIntroduction TroubleshootingAppendix B V.90 Support Glossary of Terms MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Index IndexConfiguration MT4X56USB Software user license agreement Speed