Multi-Tech Systems MT4X56USB Uninstalling MultiModemUSB in Windows, Select Add/Remove Hardware

Page 26

MultiModemUSB User Guide

14.The Found New Hardware Wizard dialog box is displayed with the message “Driver Files Search Results.”

Click Next >.

15.The Found New Hardware Wizard dialog box is displayed with the message “Windows has finished installing the software for this device.”

Click Finish.

Several screens are displayed indicating that all software drivers have been successfully installed. Installation is complete when no more screens appear.

16. To install the modems, go to the “Installing Your V.90 Modems (Windows 2000)” section.

Uninstalling MultiModemUSB in Windows 2000

1.From the Start menu, select Settings and then Control Panel.

2.Select Add/Remove Hardware.

3.Follow the on-line instructions until the Devices window is displayed. Select the appropriate entries to be deleted and click Next >.

4.The Uninstall Device dialog box is diplayed asking you if you are sure that you want to uninstall this device. Click Yes and then Next >.

26

MT4X56USB

Image 26

Contents MultiModemUSB Model MT4X56USB User GuidePatents User GuideRecord of Revisions TrademarksContents Glossary of Terms Index Introduction and Description MultiModemUSB User Guide FeaturesIntroduction Preview of this Guide Technical SpecificationsInstallation Introduction and DescriptionRelated Documentation Hub Front PanelModem Ports Ports 1, 2, 3, SystemUSB Type B Downstream Connector RJ-ll Modem ConnectorUSB Type a Upstream Connector Power ConnectorInstallation Safety Warning Telecom UnpackingInstallation Cabling your MT4X56USBMT4X56USB Software Loading and Configuration MT4X56USB Drivers for Windows System USB SupportLoading your Driver Software Software Loading and Configuration Uninstalling MultiModemUSB in Windows MT4X56USB Drivers for Windows Uninstalling MultiModemUSB in Windows MultiModemUSB Drivers Install dialog box displays Click Next MT4X56USB Drivers for Windows NTAdd/Remove Uninstalling MultiModemUSB in Windows NTSelect Add/Remove Programs MT4X56USB Drivers for Windows Click Finish Software Loading and Configuration Select Add/Remove Hardware Installing Your V.90 Modems Click Start Settings Control Panel ModemsRead Carefully Software Loading and Configuration MT4X56USB Installing Your V.90 Modems Windows Click Start Settings Control Panel Phone and Modems optionMT4X56USB Software Loading and Configuration Windows 95/98 Configuration Utility MT4X56USB Windows NT 4.0/2000 Configuration Utility MT4X56USB MT4X56USB AT Commands, S-Registers and Result Codes Repeat Last Command AT Command SummaryCommand Enter Key AnswerAT Commands, S-Registers and Result Codes Information Request Return Online to Data ModeResult Codes Enable/Disable Modulation HandshakeTone Dialing Modem ResetLoad Factory Settings Result Code FormatTest Commands Communications ModeAsynchronous Communications Mode Display Current SettingsCommand &Zy=x Store Dialing Command Store Current ConfigurationSelect Stored Configuration for Hard Reset \An Select Maximum MNP Block Size\Kn Break Control \Nn Error Correction Mode Selection\Tn Inactivity Timer \Qn Flow Control SelectionEnter Setup Password Command %DCn AT Command ControlCommand %En Fallback and Fall Forward Control Command #S=x Store Setup PasswordCommand +++ATCR Escape Sequence Command %%%ATCRRemote Configuration Escape SequenceRegister Unit Range Default Description RegistersS38 Upstream data ratesResult Codes Terse Verbose DescriptionFor more information on scripting, click the Help button Remote Configuration Changing the Setup Password Remote Configuration ProcedureSetup Changing the Remote Escape Character Remote Configuration CommandsRemote Configuration and Management MT4X56USB Troubleshooting Modem Dials But Cannot Connect None of the Indicators LightModem Does Not Respond to Commands Troubleshooting Modem Disconnects While OnlineModem Doesn’t Work with Caller ID Modem Cannot Connect When AnsweringLoopback Tests Fax and Data Software Can’t Run at the Same TimeTest procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Remote digital loopback testLocal Digital Loopback Test V.54 Loop Local digital loopback testInstalling Microsoft USB Support Windows 95/98 TroubleshootingDetermining Why USB Support Is Not Present Double-click the Universal Serial Bus Controller iconUpgrade Procedure Identify the Current Firmware Version Upgrade OverviewIdentify the MT4X56USB Firmware Multi-Tech Web SiteUpgrade Procedure Download the Upgrade FileExtract the Upgrade Files Clear Your Stored ParamentersUpgrade the Modem’s Firmware Restore Your ParametersService, Warranty and Tech Support Software User License Agreement Service, Warranty and Tech Support Limited WarrantyOn-line Warranty Registration Tech SupportService Contacting Tech Support via E-mailAppendices FCC Part Appendix a Regulatory InformationClass B Statement Industry CanadaFCC Part 68 Telecom AppendicesFAX Branding Statement Canadian Limitations NoticeNew Zealand Telecom Warning Notice EMC, Safety and Terminal Directive ComplianceCommission Decision CTR21 International Modem RestrictionsIntroduction TroubleshootingAppendix B V.90 Support Glossary of Terms MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Index IndexConfiguration MT4X56USB Software user license agreement Speed