Multi-Tech Systems manual MT4X56USB Drivers for Windows NT

Page 21

Chapter 3 - Software Loading and Configuration

MT4X56USB Drivers for Windows NT 4.0

Because NT 4.0 does not support USB, Multi-Tech provides a USB stack that will be installed along with the necessary drivers. To do this, you must have have NT Service Pack 3.00 or higher and an account that has administrative privileges.

Note: “Plug-and-Play” operations are not supported in an NT 4.0 (or earlier) operating system.

1.Ensure that power to the MT4X56USB is on but that the USB cable remains disconnected.

2.Insert the MT4X56USB Disk 2 into drive A.

3.Click Start Run.

4.Type A:\setup and click OK.

5.The install program prompts you to make certain you have NT Service Pack 3.00 or higher. Click Yes to continue.

6.The MultiModemUSB Drivers Install dialog box displays.

Click Next >.

7.The Read Multi-Tech Software License agreement screen is displayed. Read carefully. If you accept the terms of the agreement, click Yes.

8.The Release Notes screen is displayed (Release Notes can also be found after installation in the Start menu under Programs Multi-Tech USB Utilities).

Click Next >.

MT4X56USB

21

Image 21

Contents User Guide MultiModemUSB Model MT4X56USBRecord of Revisions User GuidePatents TrademarksContents Glossary of Terms Index Introduction and Description Features IntroductionMultiModemUSB User Guide Installation Technical SpecificationsPreview of this Guide Introduction and DescriptionRelated Documentation Modem Ports Ports 1, 2, 3, Front PanelHub SystemUSB Type a Upstream Connector RJ-ll Modem ConnectorUSB Type B Downstream Connector Power ConnectorInstallation Unpacking Safety Warning TelecomCabling your MT4X56USB InstallationMT4X56USB Software Loading and Configuration System USB Support Loading your Driver SoftwareMT4X56USB Drivers for Windows Software Loading and Configuration Uninstalling MultiModemUSB in Windows MT4X56USB Drivers for Windows Uninstalling MultiModemUSB in Windows MT4X56USB Drivers for Windows NT MultiModemUSB Drivers Install dialog box displays Click NextUninstalling MultiModemUSB in Windows NT Select Add/Remove ProgramsAdd/Remove MT4X56USB Drivers for Windows Click Finish Software Loading and Configuration Select Add/Remove Hardware Click Start Settings Control Panel Modems Installing Your V.90 ModemsRead Carefully Software Loading and Configuration MT4X56USB Click Start Settings Control Panel Phone and Modems option Installing Your V.90 Modems WindowsMT4X56USB Software Loading and Configuration Windows 95/98 Configuration Utility MT4X56USB Windows NT 4.0/2000 Configuration Utility MT4X56USB MT4X56USB AT Commands, S-Registers and Result Codes Command Enter Key AT Command SummaryRepeat Last Command AnswerAT Commands, S-Registers and Result Codes Result Codes Enable/Disable Return Online to Data ModeInformation Request Modulation HandshakeLoad Factory Settings Modem ResetTone Dialing Result Code FormatAsynchronous Communications Mode Communications ModeTest Commands Display Current SettingsSelect Stored Configuration for Hard Reset Store Current ConfigurationCommand &Zy=x Store Dialing Command \An Select Maximum MNP Block Size\Tn Inactivity Timer \Nn Error Correction Mode Selection\Kn Break Control \Qn Flow Control SelectionCommand %En Fallback and Fall Forward Control Command %DCn AT Command ControlEnter Setup Password Command #S=x Store Setup PasswordCommand %%%ATCRRemote Configuration Escape Sequence Command +++ATCR Escape SequenceRegisters Register Unit Range Default DescriptionUpstream data rates S38Terse Verbose Description Result CodesFor more information on scripting, click the Help button Remote Configuration Remote Configuration Procedure SetupChanging the Setup Password Remote Configuration Commands Remote Configuration and ManagementChanging the Remote Escape Character MT4X56USB Troubleshooting None of the Indicators Light Modem Does Not Respond to CommandsModem Dials But Cannot Connect Modem Disconnects While Online TroubleshootingLoopback Tests Modem Cannot Connect When AnsweringModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeLocal Analog Loopback Test V.54 Loop Test procedureRemote digital loopback test Remote Digital Loopback Test V.54 LoopLocal digital loopback test Local Digital Loopback Test V.54 LoopDetermining Why USB Support Is Not Present Windows 95/98 TroubleshootingInstalling Microsoft USB Support Double-click the Universal Serial Bus Controller iconUpgrade Procedure Identify the MT4X56USB Firmware Upgrade OverviewIdentify the Current Firmware Version Multi-Tech Web SiteExtract the Upgrade Files Download the Upgrade FileUpgrade Procedure Clear Your Stored ParamentersRestore Your Parameters Upgrade the Modem’s FirmwareService, Warranty and Tech Support Software User License Agreement On-line Warranty Registration Limited WarrantyService, Warranty and Tech Support Tech SupportContacting Tech Support via E-mail ServiceAppendices Class B Statement Appendix a Regulatory InformationFCC Part Industry CanadaAppendices FCC Part 68 TelecomCanadian Limitations Notice FAX Branding StatementCommission Decision CTR21 EMC, Safety and Terminal Directive ComplianceNew Zealand Telecom Warning Notice International Modem RestrictionsTroubleshooting Appendix B V.90 SupportIntroduction Glossary of Terms MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Index IndexConfiguration MT4X56USB Software user license agreement Speed