Multi-Tech Systems MT4X56USB manual Result Codes, Terse Verbose Description

Page 51

Chapter 4 - AT Commands, S-Registers and Result Codes

Result Codes

In command mode your modem can send responses called result codes to your computer. Result codes are used by communications programs and can also appear on your monitor.

Terse

Verbose

Description

0

 

OK

Command executed

1

 

CONNECT

Modem connected to line

2

 

RING

Ring signal detected

3

 

NO CARRIER

Carrier signal lost or not detected

4

 

ERROR

Invalid command

5

*

CONNECT 1200

Connected at 1200 bps

6

 

NO DIALTONE

No dial tone detected

7

 

BUSY

Busy signal detected

8

 

NO ANSWER

No answer at remote end

10

*

CONNECT 2400

Connected at 2400 bps

11

*

CONNECT 4800

Connected at 4800 bps

12

*

CONNECT 9600

Connected at 9600 bps

13

*

CONNECT 14400

Connected at 14400 bps

14

*

CONNECT 19200

Connected at 19200 bps

24

*

CONNECT 7200

Connected at 7200 bps

5

*

CONNECT 12000

Connected at 12000 bps

6

*

CONNECT 16800

Connected at 16800 bps

40

*

CONNECT 300

Connected at 300 bps

55

*

CONNECT 21600

Connected at 21600 bps

56

*

CONNECT 24000

Connected at 24000 bps

57

*

CONNECT 26400

Connected at 26400 bps

58

*

CONNECT 28800

Connected at 28800 bps

59

*

CONNECT 31200

Connected at 31200 bps

60

*

CONNECT 33600

Connected at 33600 bps

0

*

CONNECT 32000

Connected at 32000 bps, 56K rate

71

*

CONNECT 34000

Connected at 34000 bps, 56K rate

72

*

CONNECT 36000

Connected at 36000 bps, 56K rate

73

*

CONNECT 38000

Connected at 38000 bps, 56K rate

74

*

CONNECT 40000

Connected at 40000 bps, 56K rate

75

*

CONNECT 42000

Connected at 42000 bps, 56K rate

76

*

CONNECT 44000

Connected at 44000 bps, 56K rate

77

*

CONNECT 46000

Connected at 46000 bps, 56K rate

78

*

CONNECT 48000

Connected at 48000 bps, 56K rate

79

*

CONNECT 50000

Connected at 50000 bps, 56K rate

80

*

CONNECT 52000

Connected at 52000 bps, 56K rate

81

*

CONNECT 54000

Connected at 54000 bps, 56K rate

82

*

CONNECT 56000

Connected at 56000 bps, 56K rate

88

 

DELAYED

Delay is in effect for the dialed number

89

 

BLACKLISTED

Dialed number is blacklisted

90

 

BLACKLIST FULL

Blacklist is full

100CONNECT 28000 Connected at 28000 bps, V.90 rate

101CONNECT 29333 Connected at 29333 bps, V.90 rate

102CONNECT 30666 Connected at 30666 bps, V.90 rate

103CONNECT 33333 Connected at 33333 bps, V.90 rate

104CONNECT 34666 Connected at 34666 bps, V.90 rate

105CONNECT 37333 Connected at 37333 bps, V.90 rate

106CONNECT 38666 Connected at 38666 bps, V.90 rate

107CONNECT 41333 Connected at 41333 bps, V.90 rate

108CONNECT 42666 Connected at 42666 bps, V.90 rate

109CONNECT 45333 Connected at 45333 bps, V.90 rate

110CONNECT 46666 Connected at 46666 bps, V.90 rate

111CONNECT 49333 Connected at 49333 bps, V.90 rate

112CONNECT 50666 Connected at 50666 bps, V.90 rate

113CONNECT 53333 Connected at 53333 bps, V.90 rate

114CONNECT 54666 Connected at 54666 bps, V.90 rate

MT4X56USB

51

Image 51
Contents User Guide MultiModemUSB Model MT4X56USBTrademarks User GuideRecord of Revisions PatentsContents Glossary of Terms Index Introduction and Description Features IntroductionMultiModemUSB User Guide Introduction and Description Technical SpecificationsInstallation Preview of this GuideRelated Documentation System Front PanelModem Ports Ports 1, 2, 3, HubPower Connector RJ-ll Modem ConnectorUSB Type a Upstream Connector USB Type B Downstream ConnectorInstallation Unpacking Safety Warning TelecomCabling your MT4X56USB InstallationMT4X56USB Software Loading and Configuration System USB Support Loading your Driver SoftwareMT4X56USB Drivers for Windows Software Loading and Configuration Uninstalling MultiModemUSB in Windows MT4X56USB Drivers for Windows Uninstalling MultiModemUSB in Windows MT4X56USB Drivers for Windows NT MultiModemUSB Drivers Install dialog box displays Click NextUninstalling MultiModemUSB in Windows NT Select Add/Remove ProgramsAdd/Remove MT4X56USB Drivers for Windows Click Finish Software Loading and Configuration Select Add/Remove Hardware Click Start Settings Control Panel Modems Installing Your V.90 ModemsRead Carefully Software Loading and Configuration MT4X56USB Click Start Settings Control Panel Phone and Modems option Installing Your V.90 Modems WindowsMT4X56USB Software Loading and Configuration Windows 95/98 Configuration Utility MT4X56USB Windows NT 4.0/2000 Configuration Utility MT4X56USB MT4X56USB AT Commands, S-Registers and Result Codes Answer AT Command SummaryCommand Enter Key Repeat Last CommandAT Commands, S-Registers and Result Codes Modulation Handshake Return Online to Data ModeResult Codes Enable/Disable Information RequestResult Code Format Modem ResetLoad Factory Settings Tone DialingDisplay Current Settings Communications ModeAsynchronous Communications Mode Test Commands\An Select Maximum MNP Block Size Store Current ConfigurationSelect Stored Configuration for Hard Reset Command &Zy=x Store Dialing Command\Qn Flow Control Selection \Nn Error Correction Mode Selection\Tn Inactivity Timer \Kn Break ControlCommand #S=x Store Setup Password Command %DCn AT Command ControlCommand %En Fallback and Fall Forward Control Enter Setup PasswordCommand %%%ATCRRemote Configuration Escape Sequence Command +++ATCR Escape SequenceRegisters Register Unit Range Default DescriptionUpstream data rates S38Terse Verbose Description Result CodesFor more information on scripting, click the Help button Remote Configuration Remote Configuration Procedure SetupChanging the Setup Password Remote Configuration Commands Remote Configuration and ManagementChanging the Remote Escape Character MT4X56USB Troubleshooting None of the Indicators Light Modem Does Not Respond to CommandsModem Dials But Cannot Connect Modem Disconnects While Online TroubleshootingFax and Data Software Can’t Run at the Same Time Modem Cannot Connect When AnsweringLoopback Tests Modem Doesn’t Work with Caller IDLocal Analog Loopback Test V.54 Loop Test procedureRemote digital loopback test Remote Digital Loopback Test V.54 LoopLocal digital loopback test Local Digital Loopback Test V.54 LoopDouble-click the Universal Serial Bus Controller icon Windows 95/98 TroubleshootingDetermining Why USB Support Is Not Present Installing Microsoft USB SupportUpgrade Procedure Multi-Tech Web Site Upgrade OverviewIdentify the MT4X56USB Firmware Identify the Current Firmware VersionClear Your Stored Paramenters Download the Upgrade FileExtract the Upgrade Files Upgrade ProcedureRestore Your Parameters Upgrade the Modem’s FirmwareService, Warranty and Tech Support Software User License Agreement Tech Support Limited WarrantyOn-line Warranty Registration Service, Warranty and Tech SupportContacting Tech Support via E-mail ServiceAppendices Industry Canada Appendix a Regulatory InformationClass B Statement FCC PartAppendices FCC Part 68 TelecomCanadian Limitations Notice FAX Branding StatementInternational Modem Restrictions EMC, Safety and Terminal Directive ComplianceCommission Decision CTR21 New Zealand Telecom Warning NoticeTroubleshooting Appendix B V.90 SupportIntroduction Glossary of Terms MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Glossary MT4X56USB Index IndexConfiguration MT4X56USB Software user license agreement Speed