LevelOne WPS 0100, WPS-100USB manual Windows Peer-to-peer Print Driver, Setup

Page 19

Windows Peer-to-peer Print Driver

With this printing method, print jobs are stored (queued) on your PC, and then sent to the LevelOne Printer Server when it is available.

Setup

Before performing the following procedure, the LevelOne Printer Server must be installed on your LAN, and configured as described in Chapter 3. Both the LevelOne Printer Server and the attached printer should be powered ON.

1.Insert the supplied CD-ROM into your drive. If the setup program does not start automatically, run SETUP in the root folder.

2.Select the Installation icon, then choose the User option in the "Setup Type" screen. This will install the Peer-to-peer Print Driver.

3.Follow the prompts to complete the installation. (Refer to the Windows section of Chapter 8 - Troubleshooting if there is a problem with the installation.)

4.The Print Driver Setup will then run.

5.The LAN will be searched for LevelOne Printer Servers, and a screen like the following will be displayed.

∙If desired, change the Workgroup name and click Refresh.

∙Select List all LevelOne Printer Servers to list all LevelOne Printer Servers, regardless of Workgroup.

∙The name of the attached printer will be displayed if possible. If "No printer" is displayed, check that the printer is properly connected and powered on.

Figure 2: Printer Port Setup (Peer-to-peer Print Driver)

Page 16

Image 19

Contents User Guide Table of Contents Appendix a Specifications TroubleshootingAppendix B Network Server Configuration Introduction FeaturesSafety Instructions Models Package ContentsWPS-0100 LAN LED To generate a Diagnostic print out LED IndicatorsDiagnostic Push Button To restore the factory default settingsPage Procedure LAN InstallationCheck the LEDs LevelOne Printer Server ConfigurationUsing the Windows Wizard ProcedureAlternatives to the Windows Wizard Wireless ConfigurationIf the desired LevelOne Printer Server is not listed Quickset Advanced Configuration and ManagementWEP Settings Client PC ConfigurationWireless Settings for client PCs Ad-hoc Mode Infrastructure ModeWhich printing method should I use? Printing MethodsChecking your Network Protocols Windows Network Configuration Windows Peer-to-peer Print Driver SetupIf your LevelOne Printer Server is not listed Configure Printer PortPort Options ManagementBanner PortRetry Interval Network Neighborhood Windows SMB PrintingPrinting from MS-DOS Programs Windows with Server-based Print QueuesNdps Manager Client Windows using NdpsSoftware Requirements AppleTalk SetupAdvanced Setup and Management Macintosh AppleTalkCommunication Protocol. Enter no for Ascii or YES for Binary AppleTalk SettingsPage Additional Recommendations BiAdmin Management UtilityInstallation RequirementsMain Screen OperationGroups Status Icons Device ListDevice Information Configuration IconsTCP/IP Configuration AppleTalk ConfigurationMenu Options InitDevice Menu Print Test Configuration MenuDiagnostics menu Control MenuPreparation Web Interface SetupConfiguration Screens Connecting to the LevelOne Printer ServerAppleTalk Response Time If ErrorNetBEUI Domain NameNetWare LevelOne Printer Server ModeGeneral Management Stations Snmp Simple Network Management ProtocolConnection Trap ReceiversServer Name Configure ServerPassword Enable ProtocolsWireless Screen WEP Data Privacy Configuration128 Bit AuthenticationKey Printer Ports Serial Port ConfigurationOther Screens Server StatusIPP Server Configuration Special FeaturesInternet Printing Protocol IPP IPP Client Configuration Windows 95/98/ME/NT IPP Client Setup Windows 95/98/ME/NTInstalling from the CD-ROM Installing using IPPCLIENT.EXEOpen the Printers folder Start Settings Printers Changing the IPP Port SettingsParallel Port 3 if exists IPP Client Setup WindowsWindows 2000 No printer driver Using IPP PrintersInternet LevelOne Printer Server Internet Mail PrintingSystem Requirements Mail ServerInternet Mail Printing Configuration User Software Installation User SoftwarePort Name Using the new Port Printing through the Internet Canceling a Print JobChecking the Printer Driver Trap Receiving Station Settings Configuring the LevelOne Printer Server for SnmpSnmp Settings Management Station SettingsRequired configuration Wireless ConfigurationModels WPS-0100 & WPS-0100USB WEP Settings BiAdmin Wireless Screen Enabled WEP DisabledEncryption Link Info Screen Wireless Link Info ScreenIf using TCP/IP TroubleshootingHardware & LAN Problems Problem No All the LevelOne Printer Servers LEDs are offAppleTalk Macintosh Page Novell NetWare To remove an existing printer port installation Windows Printing ProblemsPage ∙ Then select File Properties Details Problem No WPS-0100 SpecificationsGeneral Specifications Environmental Specifications all ModelsOther Models Parallel Port Pin AssignmentsProtocol Support Feature SupportPreparing for TCP/IP Printing Network Server ConfigurationRegulatory Approvals Windows NT ServerWindows Adding a TCP/IP Remote PrinterSetup Wizard Configuration Methods Bindery or NDSWindows 2000 Server Other Methods Configuration DataBiAdmin Novell Remote Printer ModeCreating an Ndps Manager Object Setup for Ndps NetWareNovell LevelOne Printer Server Mode OverviewAt the Identification page, click the Printer Agent List Creating an Ndps Printer AgentSelect Novell Printer Gateway in the Gateway Type. see above ∙ LPD ∙ FTP Unix Systems