LevelOne WPS-100USB, WPS 0100 manual AppleTalk Macintosh

Page 64

LevelOne Printer Server.

Solution No. 5 If the LevelOne Printer Server is left on, but the DHCP server is turned off, then the LevelOne Printer Server will retain its IP Address without the DHCP Server being aware of it. Simply reset the LevelOne Printer Server so it will obtain a new IP Address.

This problem would also arise if you assigned static IP Address, which is within the range used by the DHCP server. If so, use another address which is NOT within the range used by the DHCP server.

AppleTalk (Macintosh)

Problem No. 1

 

Why do I get an incorrect printout?

 

 

 

 

 

 

Solution No. 1

 

Some possible reasons are:

 

 

∙

You may have chosen Binary encoding to print the file. Try to use

 

 

 

ASCII encoding.

 

 

∙

Some of the fonts, which are in your print file may not be

 

 

 

supported by the printer. Try selecting LaserWriter 7 instead of

 

 

 

LaserWriter 8.

 

 

 

 

 

 

Problem No. 2

 

Can't find the LevelOne Printer Server's name in the Chooser.

 

 

 

 

 

 

Solution No. 2

 

Try the following:

 

 

1.

Make sure that AppleTalk is on (the button next to Active is

 

 

 

highlighted in the Chooser).

 

 

2.

Make sure the printer has been on and in the READY state for a

 

 

 

few minutes.

 

 

3.

Make sure the printer has not been renamed since its last

 

 

 

appearance in the Chooser.

 

 

4.

If the printer resides on a network with multiple zones, make sure

 

 

 

the correct zone is selected from the AppleTalk Zones box in the

 

 

 

Chooser.

 

 

 

Problem No. 3

 

My document didn't print to the right printer.

 

 

 

 

 

 

Solution No. 3

 

Check the following:

 

 

∙

Another LevelOne Printer Server with the same name may have

 

 

 

received your print job. Use the PSTOOL to reconfigure your

 

 

 

LevelOne Printer Server name and ensure all LevelOne Printer

 

 

 

Servers have unique names.

 

 

∙

Make sure your application output encode is set to ASCII. If not,

 

 

 

change it to ASCII.

 

 

 

 

 

 

Problem No. 4

 

My file doesn't print with the correct fonts.

 

 

 

 

 

 

Solution No. 4

 

Try changing your printer driver to LaserWriter 7.

 

 

 

 

 

 

Problem No. 5

 

My EPS file doesn't print with the correct fonts.

 

 

 

 

 

 

Solution No. 5

 

This is a problem that occurs in some application programs. Try

 

 

downloading the fonts contained in the EPS file before printing the

 

 

saved EPS file.

 

 

 

 

Page 61

Page 63 Page 65
Image 64
Page 63 Page 65
Contents User Guide Table of Contents Appendix a Specifications TroubleshootingAppendix B Network Server Configuration Features IntroductionSafety Instructions Package Contents ModelsWPS-0100 LAN LED LED Indicators Diagnostic Push ButtonTo restore the factory default settings To generate a Diagnostic print outPage LAN Installation ProcedureCheck the LEDs Configuration Using the Windows WizardProcedure LevelOne Printer ServerAlternatives to the Windows Wizard Wireless ConfigurationIf the desired LevelOne Printer Server is not listed Advanced Configuration and Management QuicksetClient PC Configuration Wireless Settings for client PCsAd-hoc Mode Infrastructure Mode WEP SettingsWhich printing method should I use? Printing MethodsChecking your Network Protocols Windows Network Configuration Setup Windows Peer-to-peer Print DriverConfigure Printer Port If your LevelOne Printer Server is not listedManagement Port OptionsBanner PortRetry Interval Windows SMB Printing Network NeighborhoodWindows with Server-based Print Queues Printing from MS-DOS ProgramsWindows using Ndps Ndps Manager ClientAppleTalk Setup Advanced Setup and ManagementMacintosh AppleTalk Software RequirementsAppleTalk Settings Communication Protocol. Enter no for Ascii or YES for BinaryPage BiAdmin Management Utility InstallationRequirements Additional RecommendationsMain Screen OperationGroups Device List Status IconsConfiguration Icons TCP/IP ConfigurationAppleTalk Configuration Device InformationMenu Options InitDevice Menu Configuration Menu Diagnostics menuControl Menu Print TestWeb Interface Setup PreparationConfiguration Screens Connecting to the LevelOne Printer ServerAppleTalk If Error NetBEUIDomain Name Response TimeNetWare LevelOne Printer Server ModeGeneral Snmp Simple Network Management Protocol Management StationsTrap Receivers ConnectionConfigure Server PasswordEnable Protocols Server NameWireless Screen Configuration WEP Data Privacy128 Bit AuthenticationKey Serial Port Configuration Other ScreensServer Status Printer PortsIPP Server Configuration Special FeaturesInternet Printing Protocol IPP IPP Client Setup Windows 95/98/ME/NT Installing from the CD-ROMInstalling using IPPCLIENT.EXE IPP Client Configuration Windows 95/98/ME/NTChanging the IPP Port Settings Open the Printers folder Start Settings PrintersIPP Client Setup Windows Parallel Port 3 if existsUsing IPP Printers Windows 2000 No printer driverInternet Mail Printing System RequirementsMail Server Internet LevelOne Printer ServerInternet Mail Printing Configuration User Software Installation User SoftwarePort Name Using the new Port Printing through the Internet Canceling a Print JobChecking the Printer Driver Configuring the LevelOne Printer Server for Snmp Snmp SettingsManagement Station Settings Trap Receiving Station SettingsRequired configuration Wireless ConfigurationModels WPS-0100 & WPS-0100USB WEP Settings BiAdmin Wireless Screen Enabled WEP DisabledEncryption Wireless Link Info Screen Link Info ScreenTroubleshooting Hardware & LAN ProblemsProblem No All the LevelOne Printer Servers LEDs are off If using TCP/IPAppleTalk Macintosh Page Novell NetWare Windows Printing Problems To remove an existing printer port installationPage ∙ Then select File Properties Details Problem No Specifications General SpecificationsEnvironmental Specifications all Models WPS-0100Parallel Port Pin Assignments Other ModelsFeature Support Protocol SupportNetwork Server Configuration Regulatory ApprovalsWindows NT Server Preparing for TCP/IP PrintingAdding a TCP/IP Remote Printer WindowsSetup Wizard Configuration Methods Bindery or NDSWindows 2000 Server Configuration Data BiAdminNovell Remote Printer Mode Other MethodsSetup for Ndps NetWare Novell LevelOne Printer Server ModeOverview Creating an Ndps Manager ObjectCreating an Ndps Printer Agent At the Identification page, click the Printer Agent ListSelect Novell Printer Gateway in the Gateway Type. see above Unix Systems ∙ LPD ∙ FTP
Top Page Image Contents