LevelOne WPS-100USB, WPS 0100 manual InitDevice Menu

Page 34

InitDevice Menu

Attach Remote	This is used to connect to a LevelOne Printer Server device on another
	LAN segment. If your LAN does not have a Router, ignore this option.
Connected	This option allows you to designate which LAN protocol will be used
Protocol	for communication between the selected device and this application.
	You should select ONE protocol only.
Find	Use this option to use the IPX/SPX protocol to locate a LevelOne
	Printer Server on the LAN. Simply enter the Default Name of the
	LevelOne Printer Server you wish to locate. The Default Server Name
	is shown on a sticker on the base of the device.
Reset Device	This will cause the device to reboot. This should be done after making
	any configuration changes, or if the device stops responding after some
	problems.
Restore Factory	This will restore ALL device values to their factory defaults. To restore
Default	only the current screen, use the Set to Default button on the screen.
Set IP Address	For TCP/IP networks only:
	∙ If a LevelOne Printer Server does not appear on the main screen,
	use this option to set a Device IP Address, Gateway IP Address,
	and Network Mask to the LevelOne Printer Server.
	∙ This should only be necessary if your LAN is using ONLY the
	TCP/IP protocol. In other cases, BiAdmin will use IPX/SPX to
	locate the LevelOne Printer Server even if it doesn't have a valid
	IP Address.
	∙ To locate the LevelOne Printer Server, enter the Default Name .
	The Default Server Name is shown on a sticker on the base of the
	device.
	∙ Enter the required IP Address, Network Mask, and Gateway IP
	Address.
	∙ After saving the data to the device, refresh the listing. The
	LevelOne Printer Server should then appear in the device list on
	the main screen.
Upgrade	Upgrade the firmware in a LevelOne Printer Server. See Upgrade Icon
	for details.

Page 31

Image 34

Contents User Guide Table of Contents Appendix a Specifications TroubleshootingAppendix B Network Server Configuration Features IntroductionSafety Instructions Package Contents ModelsWPS-0100 LAN LED To restore the factory default settings LED IndicatorsDiagnostic Push Button To generate a Diagnostic print outPage LAN Installation ProcedureCheck the LEDs Procedure ConfigurationUsing the Windows Wizard LevelOne Printer ServerAlternatives to the Windows Wizard Wireless ConfigurationIf the desired LevelOne Printer Server is not listed Advanced Configuration and Management QuicksetAd-hoc Mode Infrastructure Mode Client PC ConfigurationWireless Settings for client PCs WEP SettingsWhich printing method should I use? Printing MethodsChecking your Network Protocols Windows Network Configuration Setup Windows Peer-to-peer Print DriverConfigure Printer Port If your LevelOne Printer Server is not listedManagement Port OptionsBanner PortRetry Interval Windows SMB Printing Network NeighborhoodWindows with Server-based Print Queues Printing from MS-DOS ProgramsWindows using Ndps Ndps Manager ClientMacintosh AppleTalk AppleTalk SetupAdvanced Setup and Management Software RequirementsAppleTalk Settings Communication Protocol. Enter no for Ascii or YES for BinaryPage Requirements BiAdmin Management UtilityInstallation Additional RecommendationsMain Screen OperationGroups Device List Status IconsAppleTalk Configuration Configuration IconsTCP/IP Configuration Device InformationMenu Options InitDevice Menu Control Menu Configuration MenuDiagnostics menu Print TestWeb Interface Setup PreparationConfiguration Screens Connecting to the LevelOne Printer ServerAppleTalk Domain Name If ErrorNetBEUI Response TimeNetWare LevelOne Printer Server ModeGeneral Snmp Simple Network Management Protocol Management StationsTrap Receivers ConnectionEnable Protocols Configure ServerPassword Server NameWireless Screen Configuration WEP Data Privacy128 Bit AuthenticationKey Server Status Serial Port ConfigurationOther Screens Printer PortsIPP Server Configuration Special FeaturesInternet Printing Protocol IPP Installing using IPPCLIENT.EXE IPP Client Setup Windows 95/98/ME/NTInstalling from the CD-ROM IPP Client Configuration Windows 95/98/ME/NTChanging the IPP Port Settings Open the Printers folder Start Settings PrintersIPP Client Setup Windows Parallel Port 3 if existsUsing IPP Printers Windows 2000 No printer driverMail Server Internet Mail PrintingSystem Requirements Internet LevelOne Printer ServerInternet Mail Printing Configuration User Software Installation User SoftwarePort Name Using the new Port Printing through the Internet Canceling a Print JobChecking the Printer Driver Management Station Settings Configuring the LevelOne Printer Server for SnmpSnmp Settings Trap Receiving Station SettingsRequired configuration Wireless ConfigurationModels WPS-0100 & WPS-0100USB WEP Settings BiAdmin Wireless Screen Enabled WEP DisabledEncryption Wireless Link Info Screen Link Info ScreenProblem No All the LevelOne Printer Servers LEDs are off TroubleshootingHardware & LAN Problems If using TCP/IPAppleTalk Macintosh Page Novell NetWare Windows Printing Problems To remove an existing printer port installationPage ∙ Then select File Properties Details Problem No Environmental Specifications all Models SpecificationsGeneral Specifications WPS-0100Parallel Port Pin Assignments Other ModelsFeature Support Protocol SupportWindows NT Server Network Server ConfigurationRegulatory Approvals Preparing for TCP/IP PrintingAdding a TCP/IP Remote Printer WindowsSetup Wizard Configuration Methods Bindery or NDSWindows 2000 Server Novell Remote Printer Mode Configuration DataBiAdmin Other MethodsOverview Setup for Ndps NetWareNovell LevelOne Printer Server Mode Creating an Ndps Manager ObjectCreating an Ndps Printer Agent At the Identification page, click the Printer Agent ListSelect Novell Printer Gateway in the Gateway Type. see above Unix Systems ∙ LPD ∙ FTP