LevelOne WPS-100USB manual Windows 2000 Server, Configuration Methods Bindery or NDS, Setup Wizard

Page 76

Windows 2000 Server

1.Start the Add Printer Wizard, select Network Printer, then click Next to browse for the LevelOne Printer Server.

2.Locate and double -click the LevelOne Printer Server, select the desired port, and click Next.

The following message will be displayed:

Figure 27: Windows 2000 Message

3.Click "OK", and select the correct Manufacturer and Model for this printer.

4.Follow the prompts to complete the installation.

5.In the Printers folder, right-click the new printer, and select Sharing.

∙Select "Shared As:" and enter an appropriate name for this printer. Users will see this name when browsing for the printer during installation.

∙If desired, click "Additional Drivers" and install printer drivers for other versions of Windows, such as Windows 98. This will assist users during the installation process.

6.Click OK to close this Window. Configuration is now complete.

Client PCs can now be configured as described in Chapter 4 - Client Configuration.

Novell NetWare

The LevelOne Printer Server fully supports both Bindery and NDS Novell systems.

With either Bindery or NDS, two (2) NetWare operating modes are possible - LevelOne Printer Server and Remote Printer. LevelOne Printer Server mode is recommended.

Novell Distributed Printing Services (NDPS) under NetWare 5 is also supported.

Configuration Methods (Bindery or NDS)

The following configuration methods are available. In each case, you must be logged into the required NetWare Server with ADMIN rights.

Also, if using Windows, Novell's Client32 should be installed on your PC. Without Client32, only limited configuration changes can be made on the NetWare Server.

Setup Wizard

Using the Setup Wizard is recommended. This allows configuration of the LevelOne Printer Server in NetWare LevelOne Printer Server Mode, which is the recommended system.

Page 73

Image 76

Contents User Guide Table of Contents Appendix a Specifications TroubleshootingAppendix B Network Server Configuration Features IntroductionSafety Instructions Package Contents ModelsWPS-0100 LAN LED LED Indicators Diagnostic Push ButtonTo restore the factory default settings To generate a Diagnostic print outPage LAN Installation ProcedureCheck the LEDs Configuration Using the Windows WizardProcedure LevelOne Printer ServerAlternatives to the Windows Wizard Wireless ConfigurationIf the desired LevelOne Printer Server is not listed Advanced Configuration and Management QuicksetClient PC Configuration Wireless Settings for client PCsAd-hoc Mode Infrastructure Mode WEP SettingsWhich printing method should I use? Printing MethodsChecking your Network Protocols Windows Network Configuration Setup Windows Peer-to-peer Print DriverConfigure Printer Port If your LevelOne Printer Server is not listedManagement Port OptionsBanner PortRetry Interval Windows SMB Printing Network NeighborhoodWindows with Server-based Print Queues Printing from MS-DOS ProgramsWindows using Ndps Ndps Manager ClientAppleTalk Setup Advanced Setup and ManagementMacintosh AppleTalk Software RequirementsAppleTalk Settings Communication Protocol. Enter no for Ascii or YES for BinaryPage BiAdmin Management Utility InstallationRequirements Additional RecommendationsMain Screen OperationGroups Device List Status IconsConfiguration Icons TCP/IP ConfigurationAppleTalk Configuration Device InformationMenu Options InitDevice Menu Configuration Menu Diagnostics menuControl Menu Print TestWeb Interface Setup PreparationConfiguration Screens Connecting to the LevelOne Printer ServerAppleTalk If Error NetBEUIDomain Name Response TimeNetWare LevelOne Printer Server ModeGeneral Snmp Simple Network Management Protocol Management StationsTrap Receivers ConnectionConfigure Server PasswordEnable Protocols Server NameWireless Screen Configuration WEP Data Privacy128 Bit AuthenticationKey Serial Port Configuration Other ScreensServer Status Printer PortsIPP Server Configuration Special FeaturesInternet Printing Protocol IPP IPP Client Setup Windows 95/98/ME/NT Installing from the CD-ROMInstalling using IPPCLIENT.EXE IPP Client Configuration Windows 95/98/ME/NTChanging the IPP Port Settings Open the Printers folder Start Settings PrintersIPP Client Setup Windows Parallel Port 3 if existsUsing IPP Printers Windows 2000 No printer driverInternet Mail Printing System RequirementsMail Server Internet LevelOne Printer ServerInternet Mail Printing Configuration User Software Installation User SoftwarePort Name Using the new Port Printing through the Internet Canceling a Print JobChecking the Printer Driver Configuring the LevelOne Printer Server for Snmp Snmp SettingsManagement Station Settings Trap Receiving Station SettingsRequired configuration Wireless ConfigurationModels WPS-0100 & WPS-0100USB WEP Settings BiAdmin Wireless Screen Enabled WEP DisabledEncryption Wireless Link Info Screen Link Info ScreenTroubleshooting Hardware & LAN ProblemsProblem No All the LevelOne Printer Servers LEDs are off If using TCP/IPAppleTalk Macintosh Page Novell NetWare Windows Printing Problems To remove an existing printer port installationPage ∙ Then select File Properties Details Problem No Specifications General SpecificationsEnvironmental Specifications all Models WPS-0100Parallel Port Pin Assignments Other ModelsFeature Support Protocol SupportNetwork Server Configuration Regulatory ApprovalsWindows NT Server Preparing for TCP/IP PrintingAdding a TCP/IP Remote Printer WindowsSetup Wizard Configuration Methods Bindery or NDSWindows 2000 Server Configuration Data BiAdminNovell Remote Printer Mode Other MethodsSetup for Ndps NetWare Novell LevelOne Printer Server ModeOverview Creating an Ndps Manager ObjectCreating an Ndps Printer Agent At the Identification page, click the Printer Agent ListSelect Novell Printer Gateway in the Gateway Type. see above Unix Systems ∙ LPD ∙ FTP