Vincent Audio SV-234 Do not connect PRE OUT and Main, Speaker cable connections, Protective caps

Page 31

INSTALLATION

Set up the cable links in a sequence as follows. Connect the power cable between device and power sup- ply only after all other connections have been made. Two loudspeakers, one ore more source devices and the mains cable have to be connected as a minimum. The cables for power control, to recording equipment or to another stereo amplifier must only be connected if they are to be used.

DURING INSTALLATION PLEASE OBSERVE

THE FOLLOWING ADVICE:

Do not connect PRE OUT and MAIN IN

No preamplifier-to-amplifier bridge circuit is requi- red. The input "LINE5 MAIN IN" must not be con- nected with the neighboring preamplifier output "PRE OUTPUT"! The preamplifier part of this ampli- fier is connected

internally with the power amplifier part. It is not possible to split preamplifier section and main amplifier section to

add an effects loop (for example an equalizer).

Speaker cable connections

The use of ready-made loudspeaker cables is re- commended instead of connecting the cable’s cen- tral wire (strand) directly to the terminals. Banana plugs or cable lugs ensure high security from short- circuits and damage to loudspeakers or amplifier.

Ensure that bare loudspeaker wires are never able to come into contact with each other or with the metal on the back of the housing. Ensure that bare loudspeaker wires are never able to come into con- tact with each other or with the metal on the back of the housing.

Protective caps

Prior to the first installation the pro- tective plastic caps must be removed from all the connections used at the rear of the unit.

RCA connections

1 2

OUTPUT

Make sure that the positive and negative loudspea- ker wires are connected correctly. You will notice a reduced sound quality if the connections are the wrong way round.

Only use loudspeakers with a nominal impedance of at least 4Ω.

Mechanically identical RCA plugs are available for input and output connections. Make sure that you do not get these connections confused during installation!

Cable connections

Make sure that all plugs fit tightly. Inadequate con- nections can cause noise interference, failures and malfunctions.

Make sure that you do not mix up the analogue

 

 

inputs for right and left. The RCA plugs for these

 

 

are mostly colour coded as follows: red for the

- falsely -

- right -

right channel, black or white for the left channel.

 

 

Contacting the middle pin of the RCA plugs with the outer ring of the RCA chassis jack may lead to damages to the main amplifier if it is switched on! To avoid this hazard, connect or disconnect only in switched-off state and more than one minute after deactivating!

To make the most of the components’ sound poten- tial, only high quality loudspeakers and connecting cables, for example Vincent cables, should be used. Your local stockist will be glad to advise you about this.

Vincent 31

Image 31
Contents Vincent Dear Customer Sehr geehrter KundeCher client INHALTSVERZEICHNIS/CONTENTS/SOMMAIRE Aus/Anschalten Wartung/VeränderungenAlle Betriebsmittel, die an die Netzspannung Netzkabel/AnschlussErklärungen/Hinweise Erläuterung der grafischen SymboleWeitere Hinweise CE-ZeichenBeschreibung DES Gerätes LieferumfangLEVEL/ Lautstärketasten Power NetzschalterVorderansicht AnzeigeRückansicht Power ControlBatterien FernbedienungHören möchten Gain Taste für -8dB Abschwächung aller AusgangssignaleTasten DER Fernbedienung EingangswahltastenZUR Besonderen Beachtung InstallationAnschluss Eines Quellgerätes MIT STEREO-XLR-AUSGANG Anschluss DER Quellgeräte MIT CINCH-HOCHPEGELAUSGANGKabelverbindungen FÜR DIE Einschaltsteuerung Power Control SV-234 Endverstärker Anschluss Zweier Zusätzlicher Endstufenkanäle Anschluss Eines AufnahmegerätesAnschluss DER Lautsprecher Anschluss DES Netzkabels Bedienung DES Gerätes Helligkeit der Und die Lautstärkeschritte sind zu grobGain Und REC Output 13 werden kleinerEinspielzeit/Aufwärmen Weitere TippsNetzbrummen Fehlersuche Symptom Mögliche Fehlerursache AbhilfeTechnische Daten Audio-Quellen/Audio-Quellgeräte LEXIKON/WISSENSWERTESSafety Guidelines Other Instructions Description of the Appliance Included in DeliveryFront View PRE Output Preamplifier Output Rear ViewSpeaker Loudspeaker terminals If desired, you can connect a recording deviceOld New Remote ControlUsing batteries BatteriesInput Selector Buttons Buttons of the Remote ControlLevel and Level Volume keys MuteRCA connections Do not connect PRE OUT and MainSpeaker cable connections Protective capsConnection of ONE Audio Source with XLR Output Connections for the Standby Control Power Control SV-234 is intended to react to the trigger signal Connection of TWO Additional Main Amplifier Channels Connection of a Recording DeviceConnection of the Loudspeakers Connection of the Power Cable Operating the Appliance Gain -08dB ← ... → Gain -00dB Signal output of the preamplifier PRE OutputCorresponding remote controller buttons as well as using PRE Output 14 is smallerBurn in/ Warm up TipsNet frequency noise Symptom Possible Cause Countermeasure Search for ErrorsTechnical Specifications Audio Sources/Source devices GlossaryHumidité/Chaleur/Vibrations Consignes DE SecuriteEntretien/Modifications Câble dalimentation/BranchementExplications/Remarques Explication des symboles graphiquesAutres Consignes Sigle CEDescription DE Lappareil Objet DE LA LivraisonFacade Avant LEVEL/ touches de volumeAffichage Speaker bornes de raccordement Facade ArriereInput Balanced entrée XLR Piles TelecommandeLevel et Level touches de volume Touches DE LA TélécommandeQuand l’entrée Line 5 Main Input est sélec- 19 tionnée Fiches de raccordements Pas de nécessité de liaison préampli, ampli de puissanceDépose du capot de protection Prises RCARaccordement D’UN Appareil Source Avec LA Sortie STEREO-XLR Amplificateur stéréo SV-234 Par ex. amplificateur Raccordement D’UN Appareil D’ENREGISTREMENT Branchement DES HAUT-PARLEURS Branchement DU Câble Dalimentation Commandes DE L‘APPAREIL De niveau Le volume a été augmentéProgressivité du réglage est trop grossière 8dB amortissement’expérience montre que ce phénomène est soit dû ConseilsTemps de rodage / échauffement Ronflement du secteurSymptôme Cause possible du défaut Remède Resolution DE ProblemesCaracteristiques Techniques Sources audio/lecteurs sources Lexique / BON a SavoirVincent

SV-234 specifications

The Vincent Audio SV-234 is a high-end integrated amplifier that embodies a blend of modern technology and classic audio performance, appealing to both audiophiles and casual listeners alike. This sophisticated device is designed to provide pure, dynamic sound reproduction while integrating seamlessly with various audio sources and systems.

One of the key features of the SV-234 is its dual-mono design, which enhances soundstage and imaging. The separate amplifier sections for left and right channels ensure minimal crosstalk, leading to a more immersive listening experience. This design principle is essential for delivering a clean and accurate audio signal, effectively minimizing distortion and maximizing fidelity.

The amplifier boasts an impressive power output, rated at 2 x 150 watts into 8 ohms and 2 x 240 watts into 4 ohms. This significant power output allows the SV-234 to drive a wide range of speakers effortlessly, making it suitable for various configurations, from compact bookshelf speakers to larger floor-standing models. In addition to power, the unit's class AB amplification technology provides a warm and engaging sound that appeals to discerning listeners.

In terms of connectivity, the Vincent Audio SV-234 is equipped with an array of inputs, including multiple line-level analog inputs, a phono input for turntables, and digital inputs, including USB, coaxial, and optical. This extensive selection makes it easy for users to integrate the amplifier into their existing audio setup, allowing for playback from various sources, such as CD players, streaming devices, and computers.

The SV-234 is also designed with user-friendly features, such as a remote control and a clear, intuitive front panel layout. The built-in digital-to-analog converter (DAC) enhances sound quality when using digital sources, ensuring that users receive the best possible listening experience regardless of the input method.

In terms of build quality, the SV-234 features a sturdy, elegant chassis that is both aesthetically pleasing and robust enough to withstand everyday use. The combination of high-quality components and innovative technologies makes this amplifier a testament to Vincent Audio's commitment to creating exceptional audio products.

Ultimately, the Vincent Audio SV-234 is a remarkable integrated amplifier that combines power, versatility, and exceptional sound quality. Its advanced features and thoughtful design make it an ideal choice for anyone seeking to elevate their audio experience.