Falcon SG6K-2TC, SG5K-1TXC, SG5K-2TXC, SG5K-2TC, SG6K-1TX specifications Model

Installation Instructions For Hardwire Models (see model numbers referenced below)

1.0UPS Input & Output Requirements.

IMPORTANT

Note: All SG Series hardwire UPS models must be installed by a licensed electrician, in accordance with the National Electrical Code (NEC) ANSI/NFPA70 and all local regulations. It is further required that the input of SG Series hardwire UPS be wired to a building service panel incorporating a dedicated “branch rated” circuit breaker of the proper rating.

		INPUT REQUIREMENTS
	MODEL			REQUIRED INPUT
				CIRCUIT BREAKER
SG5K-1TX:- 120Vac, 50/50Hz, 38.7A, 1 phase, 3 wire					50A
SG5K-2T - 208-240Vac, 50/60Hz, 19.5A, 1 phase, 3 wire					30A
SG5K-2TX - 208-240Vac, 50/60Hz, 20.3A, 1 phase, 3 wire					30A
SG6K-1TX - 120Vac, 50/60Hz, 46.6A, 1 phase, 3 wire					70A
SG6K-2T - 208-240Vac, 50/60Hz, 23.4A, 1 phase, 3 wire					30A
SG6K-2TX - 208-240Vac, 50/60Hz, 24.3A, 1 phase, 3 wire					30A
		WIRE GAUGE CHART
	MODEL	AC INPUT	AC OUTPUT(S)		EXTERNAL
		-1 = 120 Vac	120 Vac	208-240 Vac	BATTERY
		-2 = 208-240 Vac			240 dc
	SG5K-1TX	8 Awg. 600V	10 Awg. 600V	12 Awg. 600V	10 Awg. 600V
		75°C CU	75°C CU	75°C CU	75°C CU
	SG5K-2T	12 Awg. 600V	N/A	12 Awg. 600V	10 Awg. 600V
		75°C CU		75°C CU	75°C CU
	SG5K-2TX	12 Awg. 600V 75°C	10 Awg. 600V	12 Awg. 600V	10 Awg. 600V
		CU	75°C CU	75°C CU	75°C CU
	SG6K-1TX	6 Awg. 600V	8 Awg. 600V	10 Awg. 600V	10 Awg. 600V
		75°C CU	75°C CU	75°C CU	75°C CU
	SG6K-2T	10 Awg. 600V	N/A	10 Awg. 600V	10 Awg. 600V
		75°C CU		75°C CU	75°C CU
	SG6K-2TX	10 Awg. 600V 75°C	8 Awg. 600V	10 Awg. 600V	10 Awg. 600V
		CU	75°C CU	75°C CU	75°C CU
	External Battery &	16 Awg, 600V	N/A	N/A	10 Awg. 600V
	Charger System	75°C CU			75°C CU

ONLY USE WIRE WITH SOLID COPPER CONDUCTORS FOR ALL INPUT/OUTPUT/BATTERY WIRING

SCREW TORQUE SPECIFICATIONS FOR

INPUT/OUTPUT WIRING BLOCK

UPS & BATTERY BANK

Wire Gauge	Torque
	(inch pounds)
18 - 10 Awg.	20
8-6 Awg	25 - 30

CAUTION

To reduce the risk of fire, connect only to a circuit providing over-current protection incorporating the specified "branch rated" over-current protection device in accordance with the National Electrical Code, ANSI/NFPA 70.

7