Enterasys Networks 9034310-01, 2G4082-25 manual

Page 3

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

Notice

Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made.

The hardware, firmware, or software described in this document is subject to change without notice.

IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES.

Enterasys Networks, Inc.

50 Minuteman Road

Andover, MA 01810

♥2008 Enterasys Networks, Inc. All rights reserved. Part Number: 9034310‐01 July 2008

ENTERASYS, ENTERASYS NETWORKS, ENTERASYS MATRIX, ENTERASYS NETSIGHT, LANVIEW, WEBVIEW, and any

logos associated therewith, are trademarks or registered trademarks of Enterasys Networks, Inc., in the United States and other countries. For a complete list of Enterasys trademarks, see http://www.enterasys.com/company/trademarks.aspx.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

Documentation URL: http://www.enterasys.com/support/manuals

Documentacion URL: http://www.enterasys.com/support/manuals

Dokumentation im Internet: http://www.enterasys.com/support/manuals

i

Image 3

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Enterasys NETWORKS, INC. Firmware License Agreement Vii Viii Contents Appendix a Specifications IndexTables About This Guide Who Should Use This GuideImportant Notice Related Documents How to Use This GuideGetting Help Conventions Used in This GuideGetting Help Overview of DFE Series Capabilities Introduction2G4082-25 DFE-Platinum ModuleDFE Connectivity Switch Configuration Using WebViewSwitch Configuration Using CLI Commands Network Expansion Module NEM OptionLanview Diagnostic LEDs Secure Networks Policy SupportStandards Compatibility Lanview Diagnostic LEDs Introduction Link Aggregation Network Requirements1000BASE-SX/LX/ELX Network 10BASE-T Network100BASE-TX Network 1000BASE-T NetworkInstallation Installing Optional Network Expansion Modules Installing Module into Matrix E7 or N7 ChassisUnpacking the DFE-Platinum Module Preparation InstallationCard guides Installing Module into Matrix N1, N3, or N5 Chassis Connecting UTP Cables Connecting to the NetworkConnecting a Twisted Pair Segment to the DFE-Platinum Module RX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Connecting an IBM PC or Compatible Connecting to a VT Series TerminalConnecting a VT Series Terminal Connecting to a ModemDB9 Adapter Wiring and Signal AssignmentsModem Port Adapter Wiring and Signal Diagram First-Time Log-In Using a Console Port Connection Completing the Installation of a New System11 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User AccountViewing the Receive and Transmit Activity TroubleshootingUsing Lanview About the Management Mgmt LEDLED Alternating 67% on, 33% off Series Configuration Guide for proper setup Troubleshooting ChecklistOverview of DFE-Platinum Module Shutdown Procedure Recommended Shutdown Procedure DFE-Platinum Module Specifications SpecificationsRegulatory Compliance COM Port Pinout AssignmentsMode Switch Bank Settings Optional Installations Setting the Mode SwitchesRequired Tools Figure B-1 Mode Switch Location on 2G4082-25 Memory Locations and Replacement ProceduresFlash Dimm Replacement Procedure Location of Memory ModulesRemoving the Dimm from 2G4082-25 Figure B-3 NEM Removal and Dimm Connector Location Dimm Installing the DimmDram Simm Replacement Procedure Installing the Dram SimmRemoving the Dram Simm Figure B-7 Installing the Dram Simm Page Numerics IndexIndex-2