Enterasys Networks 9034310-01, 2G4082-25 manual DFE-Platinum Module Specifications

Page 47

A

Specifications

This appendix provides information about the following:

For information about...	Refer to page...

DFE-Platinum Module Specifications	A-1

COM Port Pinout Assignments	A-2

Regulatory Compliance	A-2

Enterasys Networks reserves the right to change the specifications at any time without notice.

DFE-Platinum Module Specifications

Table A‐1 provides the I/O ports, processors and memory, physical, and environmental module specifications for the 2G4082‐25.

Table A-1 Specifications for 2G4082-25

Item	Specification

Ports

Ports 1 through 24	Twenty-four 10BASE-T/100BASE-TX/1000BASE-T compliant
	ports through twenty-four RJ45 connectors.

Network Expansion Module option slot	Supports one optional NEM.

Processors/Memory

Processor	MPC750CX, 400 MHz processor
Dynamic Random Access Memory	128 MB
(DRAM)
FLASH Memory	32 MB

Physical

Dimensions	46.43 H x 6.05 W x 29.51 D (cm)
	18.28 H x 2.38 W x 11.62 D (in.)
Approximate Weight	Gross: 5.54 kg (12.0 lb) (shipping carton containing one
	module)
	Net: 4.10 kg (9.0 lb) (one module without packaging)

Calculated hours for Mean Time Between Failures (MTBF) for the 2G4082-25

Refer to the MTBF web site at URL http://www.enterasys.com/support/mtbf/

Matrix DFE-Platinum Series Installation Guide A-1

Image 47

Contents

Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Enterasys NETWORKS, INC. Firmware License Agreement Vii Viii Contents Tables Appendix a SpecificationsIndex Important Notice About This GuideWho Should Use This Guide Related Documents How to Use This GuideGetting Help Conventions Used in This GuideGetting Help Overview of DFE Series Capabilities Introduction2G4082-25 DFE-Platinum ModuleDFE Connectivity Switch Configuration Using WebViewSwitch Configuration Using CLI Commands Network Expansion Module NEM OptionStandards Compatibility Lanview Diagnostic LEDsSecure Networks Policy Support Lanview Diagnostic LEDs Introduction Link Aggregation Network Requirements1000BASE-SX/LX/ELX Network 10BASE-T Network100BASE-TX Network 1000BASE-T NetworkInstallation Unpacking the DFE-Platinum Module Installing Optional Network Expansion ModulesInstalling Module into Matrix E7 or N7 Chassis Preparation InstallationCard guides Installing Module into Matrix N1, N3, or N5 Chassis Connecting UTP Cables Connecting to the NetworkConnecting a Twisted Pair Segment to the DFE-Platinum Module RX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting to an IBM PC or Compatible Device Connecting to COM Port for Local ManagementWhat Is Needed Connecting an IBM PC or Compatible Connecting to a VT Series TerminalConnecting a VT Series Terminal Connecting to a ModemDB9 Adapter Wiring and Signal AssignmentsModem Port Adapter Wiring and Signal Diagram First-Time Log-In Using a Console Port Connection Completing the Installation of a New System11 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User AccountViewing the Receive and Transmit Activity TroubleshootingUsing Lanview About the Management Mgmt LEDLED Alternating 67% on, 33% off Series Configuration Guide for proper setup Troubleshooting ChecklistOverview of DFE-Platinum Module Shutdown Procedure Recommended Shutdown Procedure DFE-Platinum Module Specifications SpecificationsRegulatory Compliance COM Port Pinout AssignmentsRequired Tools Mode Switch Bank Settings Optional InstallationsSetting the Mode Switches Figure B-1 Mode Switch Location on 2G4082-25 Memory Locations and Replacement ProceduresRemoving the Dimm from 2G4082-25 Flash Dimm Replacement ProcedureLocation of Memory Modules Figure B-3 NEM Removal and Dimm Connector Location Dimm Installing the DimmRemoving the Dram Simm Dram Simm Replacement ProcedureInstalling the Dram Simm Figure B-7 Installing the Dram Simm Page Numerics IndexIndex-2

Related manuals

Manual 58 pages 25.55 Kb