Enterasys Networks 2G4082-25, 9034310-01 manual Appendix a Specifications, Index, Tables

Page 12

Recommended Shutdown Procedure	4-6
Last Resort Shutdown Procedure	4-6

Appendix A: Specifications

DFE-Platinum Module Specifications	A-1
COM Port Pinout Assignments	A-2
Regulatory Compliance	A-2

Appendix B: Mode Switch Bank Settings and Optional Installations

Required Tools			B-1
Setting the Mode Switches			B-1
Memory Locations and Replacement Procedures			B-2
Location of Memory Modules			B-3
Flash DIMM Replacement Procedure			B-3
DRAM SIMM Replacement Procedure			B-6
Index
Figures
1-1	DFE-Platinum2G4082-25 Module		1-3
3-1	Installing Module into Matrix E7 or Matrix N7 Chassis (E7 shown)		3-4
3-2	Installing Module into N3, N1, or N5 Chassis (N3 shown)		3-6
3-3	Connecting a Twisted Pair Segment to the DFE-Platinum Module		3-7
3-4	Four-Wire Crossover Cable RJ45 Pinouts, Connections Between Hub Devices		3-8
3-5	Four-WireStraight-Through Cable RJ45 Pinouts, Connections Between Switches and End User
	Devices3-8
3-6	Eight-Wire Crossover Cable RJ45 Pinouts, Connections Between Hub Devices		3-9
3-7	Eight-WireStraight-Through Cable RJ45 Pinouts, Connections	Between Switches and End-User
	Devices3-9
3-8	Connecting an IBM PC or Compatible		3-11
3-9	Connecting a VT Series Terminal		3-12
3-10	Connecting to a Modem		3-13
3-11	Matrix DFE Startup Screen Example (N7 Chassis)		3-16
4-1	LANVIEW LEDs		4-2
4-2	OFFLINE/RESET Switch		4-5
B-1	Mode Switch Location on 2G4082-25		B-2
B-2	Memory Module Locations on the 2G4082-25		B-3
B-3	NEM Removal and DIMM Connector Location		B-4
B-4	Removing the Existing DIMM		B-4
B-5	Installing the DIMM		B-5
B-6	Removing Existing DRAM SIMM		B-6
B-7	Installing the DRAM SIMM		B-7
Tables
3-1	Contents of DFE-Platinum Module Carton		3-2
4-1	LANVIEW LEDs		4-2
4-2	Troubleshooting Checklist		4-4
A-1	Specifications for 2G4082-25		A-1
A-2	COM Port Pin Assignments		A-2
A-3	Compliance Standards		A-2

x

Image 12

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Enterasys NETWORKS, INC. Firmware License Agreement Vii Viii Contents Appendix a Specifications IndexTables About This Guide Who Should Use This GuideImportant Notice How to Use This Guide Related DocumentsConventions Used in This Guide Getting HelpGetting Help Introduction Overview of DFE Series CapabilitiesDFE-Platinum Module 2G4082-25DFE Switch Configuration Using WebView Switch Configuration Using CLI CommandsNetwork Expansion Module NEM Option ConnectivityLanview Diagnostic LEDs Secure Networks Policy SupportStandards Compatibility Lanview Diagnostic LEDs Introduction Network Requirements Link Aggregation10BASE-T Network 100BASE-TX Network1000BASE-T Network 1000BASE-SX/LX/ELX NetworkInstallation Installing Optional Network Expansion Modules Installing Module into Matrix E7 or N7 ChassisUnpacking the DFE-Platinum Module Installation PreparationCard guides Installing Module into Matrix N1, N3, or N5 Chassis Connecting to the Network Connecting UTP CablesConnecting a Twisted Pair Segment to the DFE-Platinum Module RX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Connecting to a VT Series Terminal Connecting an IBM PC or CompatibleConnecting to a Modem Connecting a VT Series TerminalAdapter Wiring and Signal Assignments DB9Modem Port Adapter Wiring and Signal Diagram Completing the Installation of a New System First-Time Log-In Using a Console Port ConnectionLogging in with an Administratively-Configured User Account 11 Matrix DFE Startup Screen Example N7 ChassisTroubleshooting Using LanviewAbout the Management Mgmt LED Viewing the Receive and Transmit ActivityLED Alternating 67% on, 33% off Troubleshooting Checklist Series Configuration Guide for proper setupOverview of DFE-Platinum Module Shutdown Procedure Recommended Shutdown Procedure Specifications DFE-Platinum Module SpecificationsCOM Port Pinout Assignments Regulatory ComplianceMode Switch Bank Settings Optional Installations Setting the Mode SwitchesRequired Tools Memory Locations and Replacement Procedures Figure B-1 Mode Switch Location on 2G4082-25Flash Dimm Replacement Procedure Location of Memory ModulesRemoving the Dimm from 2G4082-25 Figure B-3 NEM Removal and Dimm Connector Location Installing the Dimm DimmDram Simm Replacement Procedure Installing the Dram SimmRemoving the Dram Simm Figure B-7 Installing the Dram Simm Page Index NumericsIndex-2