Enterasys Networks 9034310-01, 2G4082-25 manual Vcci Notice

Page 7

VCCI Notice

This is a class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

BSMI EMC Statement — Taiwan

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Safety Information

Class 1 Laser Transceivers

The single mode interface modules use Class 1 laser transceivers.

Read the following safety information before installing or operating these modules.

The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This control loop eliminates the need for maintenance checks or adjustments. The output is factory set, and does not allow any user adjustment. Class 1 Laser transceivers comply with the following safety standards:

21 CFR 1040.10 and 1040.11 U.S. Department of Health and Human Services (FDA).

IEC Publication 825 (International Electrotechnical Commission).

CENELEC EN 60825 (European Committee for Electrotechnical Standardization).

When operating within their performance limitations, laser transceiver output meets the Class 1 accessible emission limit of all three standards. Class 1 levels of laser radiation are not considered hazardous.

When the connector is in place, all laser radiation remains within the fiber. The maximum amount of radiant power exiting the fiber (under normal conditions) is ‐12.6 dBm or 55 x 10‐6 watts.

Removing the optical connector from the transceiver allows laser radiation to emit directly from the optical port. The maximum radiance from the optical port (under worst case conditions) is 0.8 W cm‐2 or 8 x 103 W m2 sr‐1.

Do not use optical instruments to view the laser output. The use of optical instruments to view laser output increases eye hazard. When viewing the output optical port, power must be removed from the network adapter.

v

Image 7
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Enterasys NETWORKS, INC. Firmware License Agreement Vii Viii Contents Index Appendix a SpecificationsTables Who Should Use This Guide About This GuideImportant Notice Related Documents How to Use This GuideGetting Help Conventions Used in This GuideGetting Help Overview of DFE Series Capabilities Introduction2G4082-25 DFE-Platinum ModuleDFE Connectivity Switch Configuration Using WebViewSwitch Configuration Using CLI Commands Network Expansion Module NEM OptionSecure Networks Policy Support Lanview Diagnostic LEDsStandards Compatibility Lanview Diagnostic LEDs Introduction Link Aggregation Network Requirements1000BASE-SX/LX/ELX Network 10BASE-T Network100BASE-TX Network 1000BASE-T NetworkInstallation Installing Module into Matrix E7 or N7 Chassis Installing Optional Network Expansion ModulesUnpacking the DFE-Platinum Module Preparation InstallationCard guides Installing Module into Matrix N1, N3, or N5 Chassis Connecting UTP Cables Connecting to the NetworkConnecting a Twisted Pair Segment to the DFE-Platinum Module RX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 What Is Needed Connecting to COM Port for Local ManagementConnecting to an IBM PC or Compatible Device Connecting an IBM PC or Compatible Connecting to a VT Series TerminalConnecting a VT Series Terminal Connecting to a ModemDB9 Adapter Wiring and Signal AssignmentsModem Port Adapter Wiring and Signal Diagram First-Time Log-In Using a Console Port Connection Completing the Installation of a New System11 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User AccountViewing the Receive and Transmit Activity TroubleshootingUsing Lanview About the Management Mgmt LEDLED Alternating 67% on, 33% off Series Configuration Guide for proper setup Troubleshooting ChecklistOverview of DFE-Platinum Module Shutdown Procedure Recommended Shutdown Procedure DFE-Platinum Module Specifications SpecificationsRegulatory Compliance COM Port Pinout AssignmentsSetting the Mode Switches Mode Switch Bank Settings Optional InstallationsRequired Tools Figure B-1 Mode Switch Location on 2G4082-25 Memory Locations and Replacement ProceduresLocation of Memory Modules Flash Dimm Replacement ProcedureRemoving the Dimm from 2G4082-25 Figure B-3 NEM Removal and Dimm Connector Location Dimm Installing the DimmInstalling the Dram Simm Dram Simm Replacement ProcedureRemoving the Dram Simm Figure B-7 Installing the Dram Simm Page Numerics IndexIndex-2