Enterasys Networks 2G4082-25 manual Logging in with an Administratively-Configured User Account

Page 40

Completing the Installation of a New System

Pin Out Descriptions

Figure 3-11 Matrix DFE Startup Screen Example (N7 Chassis)

login: admin Password:

M A T R I X N7

Command Line Interface

Enterasys Networks, Inc.

50 Minuteman Rd.

Andover, MA 01810-1008 U.S.A.

Phone: +1 978 684 1000

E-mail: support@enterasys.com

WWW:http://www.enterasys.com

(c) Copyright Enterasys Networks, Inc. 2003

Chassis Serial Number: xxxxxxxxxxxx

Chassis Firmware Revision: xx.xx.xx

Matrix N7(su)->

Logging in with an Administratively-Configured User Account

If the device’s default user account settings have been changed, proceed as follows:

1.At the login prompt, enter your administratively‐assigned user name and press Enter.

2.At the Password prompt, enter your password and press Enter.

The notice of authorization and the Matrix prompt displays as shown back in Figure 3‐11.

Note: Users with Read-Write (rw) and Read-Only (ro) access can use the set password command to change their own passwords. Administrators with Super User (su) access can use the set system login command to create and change user accounts, and the set password command to change any local account password. For information on the set password and set system login commands, refer to the Enterasys Matrix DFE-Diamond/Platinum Series Configuration Guide.

The DFE‐Platinum module is now ready to be configured. For information about setting the IP address and configuring Telnet settings for remote access to DFE management, refer to the Enterasys Matrix DFE‐Diamond/Platinum Series Configuration Guide. The CLI commands enable you to initially set up and perform more involved management configurations.

The Enterasys Matrix DFE‐Diamond/Platinum Series Configuration Guide is available online at:

http://www.enterasys.com/support/manuals

If you require assistance, contact Enterasys Networks using one of the methods described in “Getting Help” on page xiii.

3-16 Installation

Image 40

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Enterasys NETWORKS, INC. Firmware License Agreement Vii Viii Contents Index Appendix a SpecificationsTables Who Should Use This Guide About This GuideImportant Notice How to Use This Guide Related DocumentsConventions Used in This Guide Getting HelpGetting Help Introduction Overview of DFE Series CapabilitiesDFE-Platinum Module 2G4082-25DFE Switch Configuration Using WebView Switch Configuration Using CLI CommandsNetwork Expansion Module NEM Option ConnectivitySecure Networks Policy Support Lanview Diagnostic LEDsStandards Compatibility Lanview Diagnostic LEDs Introduction Network Requirements Link Aggregation10BASE-T Network 100BASE-TX Network1000BASE-T Network 1000BASE-SX/LX/ELX NetworkInstallation Installing Module into Matrix E7 or N7 Chassis Installing Optional Network Expansion ModulesUnpacking the DFE-Platinum Module Installation PreparationCard guides Installing Module into Matrix N1, N3, or N5 Chassis Connecting to the Network Connecting UTP CablesConnecting a Twisted Pair Segment to the DFE-Platinum Module RX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 What Is Needed Connecting to COM Port for Local ManagementConnecting to an IBM PC or Compatible Device Connecting to a VT Series Terminal Connecting an IBM PC or CompatibleConnecting to a Modem Connecting a VT Series TerminalAdapter Wiring and Signal Assignments DB9Modem Port Adapter Wiring and Signal Diagram Completing the Installation of a New System First-Time Log-In Using a Console Port ConnectionLogging in with an Administratively-Configured User Account 11 Matrix DFE Startup Screen Example N7 ChassisTroubleshooting Using LanviewAbout the Management Mgmt LED Viewing the Receive and Transmit ActivityLED Alternating 67% on, 33% off Troubleshooting Checklist Series Configuration Guide for proper setupOverview of DFE-Platinum Module Shutdown Procedure Recommended Shutdown Procedure Specifications DFE-Platinum Module SpecificationsCOM Port Pinout Assignments Regulatory ComplianceSetting the Mode Switches Mode Switch Bank Settings Optional InstallationsRequired Tools Memory Locations and Replacement Procedures Figure B-1 Mode Switch Location on 2G4082-25Location of Memory Modules Flash Dimm Replacement ProcedureRemoving the Dimm from 2G4082-25 Figure B-3 NEM Removal and Dimm Connector Location Installing the Dimm DimmInstalling the Dram Simm Dram Simm Replacement ProcedureRemoving the Dram Simm Figure B-7 Installing the Dram Simm Page Index NumericsIndex-2