Cypress CY7C65113C manual List of Tables

Page 4

 

 

CY7C65113C

Figure 16-5.

Hub Ports Force Low Register

31

Figure 16-6.

Hub Ports SE0 Status Register

31

Figure 16-7.

Hub Ports Data Register

32

Figure 16-8.

Hub Ports Suspend Register

32

Figure 16-9. Hub Ports Resume Status Register

33

Figure 16-10. USB Status and Control Register

33

Figure 17-1. USB Device Address Registers

34

Figure 17-2. USB Device Endpoint Zero Mode Registers

35

Figure 17-3. USB Non-control Device Endpoint Mode Registers

36

Figure 17-4.

USB Endpoint Counter Registers

36

Figure 17-5. Token/Data Packet Flow Diagram

38

 

 

LIST OF TABLES

 

Table 4-1.

Pin Assignments

8

Table 4-2. I/O Register Summary

9

Table 4-3.

Instruction Set Summary

10

Table 9-1.

GPIO Port Output Control Truth Table and Interrupt Polarity

19

Table 11-1.

 

I2C Port Configuration

20

Table 12-1.

 

I2C Status and Control Register Bit Definitions

21

Table 14-1.

 

Interrupt Vector Assignments

26

Table 16-1.

 

Control Bit Definition for Downstream Ports

31

Table 16-2.

 

Control Bit Definition for Upstream Port

34

Table 17-1. Memory Allocation for Endpoints

35

Table 18-1. USB Register Mode Encoding

39

Table 18-2.

 

Decode table for Table 18-3: “Details of Modes for Differing Traffic Condition

40

Table 18-3.

 

Details of Modes for Differing Traffic Conditions

41

Document #: 38-08002 Rev. *D

Page 4 of 49

[+] Feedback

Image 4
Contents USB Hub with Microcontroller Cypress Semiconductor CorporationCY7C65113C 16.0 17.018.0 19.0List of Tables Features Functional Overview GpioI2C USBLogic Block Diagram Pin Configurations Product Summary TablesPin Assignments Top View CY7C65113C 28-pin SoicI/O Register Summary Instruction Set Summary Instruction Set SummaryMnemonic Operand Opcode CyclesProgramming Model 14-bit Program CounterProgram Memory begins here KB -32 Prom ends here CY7C65113C8-bit Temporary Register 8-bit Accumulator a8-bit Program Stack Pointer PSP Address Modes 8-bit Data Stack Pointer DSPMOV A, Dspinit Power-on Reset ClockingXtalout XtalinSuspend Mode Watchdog ResetPort 0,1 Low Isink General-purpose I/O PortsPort 0 Data Address Gpio Configuration Port Gpio Configuration AddressGpio Interrupt Enable Ports 10.0 12-bit Free-Running TimerPort 0 Interrupt Enable 11.0 I2C Configuration Register Timer LSB AddressTimer MSB Address 2C Configuration Address12.0 I2C-compatible Controller I2C Data Address2C Status and Control Address ACKContinue/Busy Write 1 to indicate ready for next transaction Processor Status and Control Address 0xFF Processor Status and Control RegisterIRQ USB Endpoint Interrupt Enable Address Global Interrupt Enable Register AddressInterrupts Interrupt Controller Function Diagram Interrupt VectorsTimer Interrupt USB Bus Reset InterruptInterrupt Latency USB Endpoint Interrupts USB Hub InterruptGpio Interrupt 14.8 I2C InterruptUSB Overview USB Serial Interface Engine SIEUSB Enumeration ACK/NAK/STALLUSB Hub Connecting/Disconnecting a USB DeviceHub Ports Connect Status Hub Ports Enable Register Address Hub Ports Enable RegisterEnabling/Disabling a USB Device Hub Downstream Ports Status and ControlHub Ports Force Low Hub Downstream Ports Control Register Address 0x4BHub Ports SE0 Status Address 0x4F Downstream Port Suspend and Resume Hub Ports DataHub Ports Data Register Hub Ports Suspend Address 0x4DHub Ports Resume Address 0x4E USB Upstream Port Status and ControlUSB Status and Control Address 0x1F USB Serial Interface Engine Operation USB Device AddressesUSB Device Endpoints USB Device Address Device A, B Addresses 0x10A and 0x40BUSB Device Endpoint Zero Mode A0, B0 USB Control Endpoint Mode RegistersSize Label Start Address USB Non-control Endpoint Mode Registers USB Non-control Device Endpoint ModeUSB Endpoint Counter Registers StallSetup Endpoint Mode/Count Registers Update and Locking MechanismUpdate Update only if Fifo is Written DataSet Data SetUSB Mode Tables Setup OUTDtog Dval Count Dtog Dval Count Endpoint Register Summary PortsLOW Sample Schematic Absolute Maximum RatingsElectrical Characteristics Parameter Description Conditions Min Max Unit GeneralUSB Interface Upstream/Downstream PortSwitching Characteristics fOSC = 6.0 MHz USB Full-speed Signaling10Timer Signals Parameter Description Min Max Unit Clock SourcePackage Diagram Ordering InformationOrdering Code Prom Size Package Type Operating Range CY7C65113C-SXCTDocument History Issue Date Orig. Description of ChangeREV ECN no