![](/images/new-backgrounds/1147214/14721469x1.webp)
RIC-E1Installation and Operation Manual | Chapter 5 RIC-E1/R Card |
| | |
| | |
| | |
5.2 Power Supply
Power is supplied to the RIC-E1/R card from the ASM-MN-214 power supply via the chassis. Each RIC-E1/R card has two fuses (F5 and F6), which protect the entire system against power failure resulting from a short circuit in one card. The rating of the fuses is 500 mA, 250V, slowblow (see Figure 5-6).
The ASM-MN-214 card cage can accept both AC or DC power supplies. LED indicators located on the ASM-MN-214 front panel (see Figure 5-5)show activity when the power supply is connected to the mains plug. The power supply supports the full card cage with any combination of cards.
AC Supply
The AC power supply of the ASM-MN-214 is 100, 115, or 230 VAC, ±10%, 47 to 63 Hz.
DC Supply
The DC power supply is -48 VDC (-36 to -72 VDC) or 24 VDC (18 to 32 VDC). It uses a DC/DC converter module to provide the power required for the cards.
Power Supply with Redundancy
This special ordering option is equipped with two separate power supplies, operating together and sharing the load of the whole card cage. If either of the power supplies fails, the other one will continue to supply power to the full card cage.
Two LED indicators show activity of each power supply. They should both light when mains power is provided.
Note It is possible to combine AC and DC power supplies in the same cage.
Order from: Cutter Networks | Ph:727-398-5252/Fax:727-397-9610 | www.bestdatasource.com |
RIC-E1
Order from Cutter Networks Ph727-398-5252/Fax727-397-9610
International Headquarters RAD Data Communications Inc
RIC-E1
Limited Warranty
Please observe the following precautions
General Safety Instructions
Connection of DC Mains
General Safety Practices
Connection of AC Mains
Isdn
Ports Safety Status
Electromagnetic Compatibility EMC
Canadian Emission Requirements
Supplementary Information
Safety
Manufacturers Name Manufacturers Address
Product Names
Quick Start Guide
Installing RIC-E1
Setting the Internal Jumpers
Jumper Description Values Default Setting
To connect cables
Connecting the Cables
Operating RIC-E1
Contents
List of Figures
Versions
Power Supply
Chapter Introduction
Overview
Application
Physical Description
Timing Reference
Functional Block Diagram
Diagnostics
Functional Description
Internal oscillator
Technical Specifications
Receive, derived from the received signal
Derived from three alternative sources
Environment
Diagnostics
Power
Physical
Technical Specifications
Site Requirements and Prerequisites
Chapter Installation and Setup
Package Contents
To set the jumpers
Configuring RIC-E1
Setting the Jumpers
To install RIC-E1
RIC-E1 Jumper Locations RIC-E1 Jumper Settings
Closing the RIC-E1 Case
Connecting the Interfaces
Connecting the E1 Line
Selecting the Impedance
Connecting the DC Power
Connecting the Power
Connecting the DTE
Connecting the AC Power
Installation and Setup
Designation Color Function
Front Panel Indicators
Chapter Operation
Turning Off
Operating Instructions
Turning On
Operating RIC-E1
Activating Local Analog Loopback
Chapter Troubleshooting Diagnostics
Performing Local Analog Loopback
To activate the local analog loopback from RIC-E1/R
Troubleshooting
RIC-E1 Troubleshooting
Deactivating Local Analog Loopback
Technical Support
Technical Support
ASM-MN-214 Card Cage
Line Connector
DTE Connector
Chapter RIC-E1/R Card
ASM-MN-214 Rear Panel
DC Supply
Power Supply
Power Supply with Redundancy
AC Supply
IR-ETH or IR-ETH
RIC-E1/R Front Panel
ASM-MN-214 Front Panel
RIC-E1/R PCB Layout RIC-E1/R Jumper Settings
Installing the RIC-E1/R Card
Setting Internal Jumpers and Switches
To install the RIC-E1/R card in the ASM-MN-214 card cage
Installing RIC-E1/R into the ASM-MN-214 Card Cage
RIC-E1/R Card
V.35, X.21 and RS-530 Interface Connectors
Appendix a Interface Connector Wiring
Signal Function 36, 37-Pin RS-530, 25-pin Circuit
V.36 Interface Connector
Pin Function
Line Interface Connector
Table A-3. RJ-45 Line Interface Connector, Pin Assignment
Signal Function 36, 37-pin RS-530, 25-pin Pin Circuit
Appendix a Interface Connector Wiring
Introduction
Contents
Appendix B IR-ETH Interface Module
Table B-1. RJ-45 Pinout
IR-ETH Options
Standalone RIC-E1
RIC-E1/R Card
Figure B-3. RIC-E1/R with IR-ETH
Installation and Operation
Table B-2. DIP Switch Settings
Setting the DIP Switch
LED Indicators
ACT
Connecting the LAN
Table B-4. IR-ETH LED Indicators, RIC-E1/R
Link
Appendix C IR-ETH/V Interface Module
IR-ETH/V Options
RIC-E1
Data 00, 01, 02, …
For example, MDI in OFF position, MDI is enabled
Mbps full duplex, 285 ∝s
Throughput
Section Name Description Possible Settings Factory Setting
Setting the DIP Switches
Table C-2. DIP SW1 Switch Settings
Moved by the user Table C-3. DIP Switch SW2 Settings
Color Function
Table C-4. IR-ETH/V LED Indicators
Backpressure and Flow Control
Introduction
Appendix D IR-IP Interface Module
Appendix D IR-IP Interface Module
Frame Relay RFC
Connector 10BaseT Shielded RJ-45
Standard Ieee 802.3/Ethernet Data Rate
Protocols
RIC-E1/ IP
Table D-2. IR-IP LEDs Functions RIC-E1/R Card
IR-IP LEDs
IR-IP Controls
Table D-1. IR-IP LEDs Functions Standalone RIC-E1
Table D-4 RJ-45 Pinout
Control Function Values Default Setting
IR-IP Management Subsystem, General
Table D-3. IR-IP Controls
Default IP Communication Parameters
Accessing the IR-IP Management Subsystem
To allow the IR-IP configuration
Performing Preliminary Configuration
Rescue Configuration
Outline of Preliminary Configuration
IP Learning Mechanism
Connecting the Telnet Host
Preliminary Telnet Host Configuration
Assigning the Router LAN Interface Address
Assigning a LAN IP Address to a New IR-IP
To view and edit the ARP table contents
To configure the IP router LAN address
No ping replies from IR-IP
Changing the LAN IP Address of a Configured IR-IP
After RIC-E1 is turned on, the ERR indicator does not light
What to Do If
Starting a Management Utility
General Operating Procedures
IR-IP Management Utility
Menu Structure of Management Utility
Quick Setup Menu
To access the Quick Setup menu
WAN IP Address
Default Gateway
LAN IP Address
LAN IP Mask
Dhcp Relay
Read Protocol from DIP Switches
Operation with Default Gateway
To configure the IR-IP as a Dhcp relay
Protocol
Management Access Menu
Telnet Password
To access the Management Access menu
To access the Device Identification menu
Advanced Setup Menu
Telnet Inactivity Timeout
To access the Advanced Setup menu
Contact Person
To access the Interface Parameters menu
Interface Parameters Menu
Device Name
WAN Protocol Parameters Frame Relay Protocol Menu
Protocol Field Compression
Authentication Protocol
WAN Protocol Parameters PPP Protocol
Header and Control Field Compression
Multicast IP
Figure D-17. Multicast IP Menu
Multicast Forwarding
Static Groups
To access the Device Control menu
Device Control
New Software Download Menu
Viewing Error Log Screen
Resetting the LAN Interface
Erasing Configuration
Resets Menu
Resetting the Device
View Menu
Configuration and Connection
To access the View menu
To access the Configuration and Connection screen
ARP Tables
To access the ARP Tables screen
Displaying Statistics
To access the Multicast Groups Table screen
To access the Statistics menu
Multicast Groups Table Screen
To access the Diagnostic Tools menu
Diagnostic Tools Ping Terminal
To ping a host
Using the Ping Function
Desired positions, and then turn the RIC-E1 on again
Erasing User’s Configuration
To erase the user’s configuration
Erasing IR-IP Software
Case, it is recommended to turn RIC-E1 off and then back on
Erasing Application Software
Downloading New Software
To erase the application software
Appendix D IR-IP Interface Module
Rear Panel
Appendix E IR-X.21B Interface Module
Selecting the IR-X.21B Timing
EXT Clock Mode
Buffer
INT/LBT Clock Mode
IR-X.21B
Appendix E IR-X.21B Interface Module
IR-ETH
Impedance, 2-4Indicators
Index
IP-IR
Requirements, 2-1RIC-E1/R Card
IR-IP
LED
Excellent Good Fair Poor Very Poor
Customer Response Form
Error Report
Order from Cutter Networks Ph727-398-5252/Fax727-397-9610
International Headquarters