RAD Data comm RIC-E1 operation manual Electromagnetic Compatibility EMC

Page 8

Caution

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cords.

 

Attention

 

 

Pour réduire les risques s’incendie, utiliser seulement des conducteurs de

 

 

télécommunications 26 AWG ou de section supérieure.

 

 

Some ports are suitable for connection to intra-building or non-exposed wiring or cabling only. In such cases, a notice will be given in the installation instructions.

Do not attempt to tamper with any carrier-provided equipment or connection hardware.

Electromagnetic Compatibility (EMC)

The equipment is designed and approved to comply with the electromagnetic regulations of major regulatory bodies. The following instructions may enhance the performance of the equipment and will provide better protection against excessive emission and better immunity against disturbances.

A good earth connection is essential. When installing the equipment in a rack, make sure to remove all traces of paint from the mounting points. Use suitable lock-washers and torque. If an external grounding lug is provided, connect it to the earth bus using braided wire as short as possible.

The equipment is designed to comply with EMC requirements when connecting it with unshielded twisted pair (UTP) cables. However, the use of shielded wires is always recommended, especially for high-rate data. In some cases, when unshielded wires are used, ferrite cores should be installed on certain cables. In such cases, special instructions are provided in the manual.

Disconnect all wires which are not in permanent use, such as cables used for one-time configuration.

The compliance of the equipment with the regulations for conducted emission on the data lines is dependent on the cable quality. The emission is tested for UTP with 80 dB longitudinal conversion loss (LCL).

Unless otherwise specified or described in the manual, TNV-1 and TNV-3 ports provide secondary protection against surges on the data lines. Primary protectors should be provided in the building installation.

The equipment is designed to provide adequate protection against electro-static discharge (ESD). However, it is good working practice to use caution when connecting cables terminated with plastic connectors (without a grounded metal hood, such as flat cables) to sensitive data lines. Before connecting such cables, discharge yourself by touching earth ground or wear an ESD preventive wrist strap.

FCC-15 User Information

This equipment has been tested and found to comply with the limits of the Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the Installation and Operation manual, may cause harmful interference to the radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Page 7 Page 9
Image 8
Page 7 Page 9
Contents RIC-E1 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 RIC-E1 International Headquarters RAD Data Communications IncLimited Warranty General Safety Instructions Please observe the following precautionsConnection of DC Mains General Safety PracticesConnection of AC Mains Ports Safety Status IsdnElectromagnetic Compatibility EMC Canadian Emission Requirements Safety Manufacturers Name Manufacturers AddressProduct Names Supplementary InformationInstalling RIC-E1 Setting the Internal JumpersJumper Description Values Default Setting Quick Start GuideTo connect cables Connecting the CablesOperating RIC-E1 Contents List of Figures Power Supply Chapter IntroductionOverview VersionsPhysical Description ApplicationFunctional Block Diagram DiagnosticsFunctional Description Timing ReferenceTechnical Specifications Receive, derived from the received signalDerived from three alternative sources Internal oscillatorDiagnostics PowerPhysical EnvironmentTechnical Specifications Site Requirements and Prerequisites Chapter Installation and SetupPackage Contents Configuring RIC-E1 Setting the JumpersTo install RIC-E1 To set the jumpersRIC-E1 Jumper Locations RIC-E1 Jumper Settings Connecting the Interfaces Connecting the E1 LineSelecting the Impedance Closing the RIC-E1 CaseConnecting the Power Connecting the DTEConnecting the AC Power Connecting the DC PowerInstallation and Setup Designation Color Function Front Panel IndicatorsChapter Operation Operating Instructions Turning OnOperating RIC-E1 Turning OffActivating Local Analog Loopback Chapter Troubleshooting DiagnosticsPerforming Local Analog Loopback Troubleshooting RIC-E1 TroubleshootingDeactivating Local Analog Loopback To activate the local analog loopback from RIC-E1/RTechnical Support Technical Support Line Connector DTE ConnectorChapter RIC-E1/R Card ASM-MN-214 Card CageASM-MN-214 Rear Panel Power Supply Power Supply with RedundancyAC Supply DC SupplyRIC-E1/R Front Panel IR-ETH or IR-ETHASM-MN-214 Front Panel RIC-E1/R PCB Layout RIC-E1/R Jumper Settings Installing the RIC-E1/R CardSetting Internal Jumpers and Switches Installing RIC-E1/R into the ASM-MN-214 Card Cage To install the RIC-E1/R card in the ASM-MN-214 card cageRIC-E1/R Card Appendix a Interface Connector Wiring V.35, X.21 and RS-530 Interface ConnectorsV.36 Interface Connector Signal Function 36, 37-Pin RS-530, 25-pin CircuitLine Interface Connector Table A-3. RJ-45 Line Interface Connector, Pin AssignmentSignal Function 36, 37-pin RS-530, 25-pin Pin Circuit Pin FunctionAppendix a Interface Connector Wiring Introduction ContentsAppendix B IR-ETH Interface Module IR-ETH Options Standalone RIC-E1RIC-E1/R Card Table B-1. RJ-45 PinoutFigure B-3. RIC-E1/R with IR-ETH Installation and Operation Table B-2. DIP Switch Settings Setting the DIP SwitchLED Indicators Connecting the LAN Table B-4. IR-ETH LED Indicators, RIC-E1/RLink ACTAppendix C IR-ETH/V Interface Module IR-ETH/V Options RIC-E1 For example, MDI in OFF position, MDI is enabled Mbps full duplex, 285 ∝sThroughput Data 00, 01, 02, …Setting the DIP Switches Table C-2. DIP SW1 Switch SettingsMoved by the user Table C-3. DIP Switch SW2 Settings Section Name Description Possible Settings Factory SettingColor Function Table C-4. IR-ETH/V LED IndicatorsBackpressure and Flow Control Appendix D IR-IP Interface Module IntroductionAppendix D IR-IP Interface Module Connector 10BaseT Shielded RJ-45 Standard Ieee 802.3/Ethernet Data RateProtocols Frame Relay RFCRIC-E1/ IP IR-IP LEDs IR-IP ControlsTable D-1. IR-IP LEDs Functions Standalone RIC-E1 Table D-2. IR-IP LEDs Functions RIC-E1/R CardControl Function Values Default Setting IR-IP Management Subsystem, GeneralTable D-3. IR-IP Controls Table D-4 RJ-45 PinoutAccessing the IR-IP Management Subsystem Default IP Communication ParametersPerforming Preliminary Configuration Rescue ConfigurationOutline of Preliminary Configuration To allow the IR-IP configurationConnecting the Telnet Host Preliminary Telnet Host ConfigurationAssigning the Router LAN Interface Address IP Learning MechanismAssigning a LAN IP Address to a New IR-IP To view and edit the ARP table contentsTo configure the IP router LAN address Changing the LAN IP Address of a Configured IR-IP After RIC-E1 is turned on, the ERR indicator does not lightWhat to Do If No ping replies from IR-IPStarting a Management Utility General Operating ProceduresIR-IP Management Utility Menu Structure of Management Utility Quick Setup MenuTo access the Quick Setup menu Default Gateway LAN IP AddressLAN IP Mask WAN IP AddressRead Protocol from DIP Switches Operation with Default GatewayTo configure the IR-IP as a Dhcp relay Dhcp RelayManagement Access Menu Telnet PasswordTo access the Management Access menu ProtocolAdvanced Setup Menu Telnet Inactivity TimeoutTo access the Advanced Setup menu To access the Device Identification menuTo access the Interface Parameters menu Interface Parameters MenuDevice Name Contact PersonWAN Protocol Parameters Frame Relay Protocol Menu Authentication Protocol WAN Protocol Parameters PPP ProtocolHeader and Control Field Compression Protocol Field CompressionMulticast IP Multicast Forwarding Figure D-17. Multicast IP MenuStatic Groups To access the Device Control menuDevice Control Viewing Error Log Screen New Software Download MenuErasing Configuration Resets MenuResetting the Device Resetting the LAN InterfaceConfiguration and Connection To access the View menuTo access the Configuration and Connection screen View MenuTo access the ARP Tables screen ARP TablesTo access the Multicast Groups Table screen To access the Statistics menuMulticast Groups Table Screen Displaying StatisticsDiagnostic Tools Ping Terminal To access the Diagnostic Tools menuUsing the Ping Function To ping a hostErasing User’s Configuration To erase the user’s configurationErasing IR-IP Software Desired positions, and then turn the RIC-E1 on againErasing Application Software Downloading New SoftwareTo erase the application software Case, it is recommended to turn RIC-E1 off and then back onAppendix D IR-IP Interface Module Appendix E IR-X.21B Interface Module Rear PanelEXT Clock Mode Selecting the IR-X.21B TimingBuffer INT/LBT Clock ModeIR-X.21B Appendix E IR-X.21B Interface Module Impedance, 2-4Indicators IndexIP-IR IR-ETHRequirements, 2-1RIC-E1/R Card IR-IPLED Customer Response Form Excellent Good Fair Poor Very PoorError Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters
Top Page Image Contents