RAD Data comm RIC-E1 LAN IP Address, LAN IP Mask, WAN IP Address, WAN IP Mask, Default Gateway

Page 70

Appendix D IR-IP Interface Module

RIC-E1Installation and Operation Manual

 

 

LAN IP Address

Used to enter the IP address for the IP router LAN interface. This is the address to which nodes connected to the local LAN send packets addressed to the WAN.

LAN IP Mask

Used to enter the IP subnet mask. The IP router supports a maximum of 254 hosts on the LAN, therefore you must use Class C subnet masks. The basic subnet IP mask for Class C addresses, which supports the maximum possible number of hosts, 254, is 255.255.255.0. To help you understand the selection of IP subnet masks, Figure D-9provides a configuration example for a LAN with 6 nodes: the IP subnet mask for a 6-node IP network is 255.255.255.248.

RIC-E1 with IR-IP

LAN IP Address: 192.168.1.2

Mask: 255.255.255.248

IP Address

192.168.1.2

.3

.4

.5

.6

Mask

255.255.255.248

.248

.248

.248

.248

Default Gateway

192.168.1.1

192.168.1.1

192.168.1.1

192.168.1.1

192.168.1.1

Figure D-9. Selecting the IP Subnet Mask

WAN IP Address

Used to enter the IP address for the IR-IP WAN interface, i.e., the IP address to be used by IP hosts on the WAN to reach this IR-IP interface module.

If the WAN IP Address field remain blank, IR-IP operates in the Unnumbered Router Mode.

WAN IP Mask

Used to enter the IP subnet mask for the WAN interface.

Default Gateway

Operation without Default Gateway

The IP interface module is intended to enable the extension of LANs through the RIC-E1 E1 link. Therefore, its default routing operation is different from the default routing operation of standard IP routers:

•IR-IP forwards packets with destinations not located on the local LAN through the WAN interface

•Packets received from the WAN interface and destined to hosts located on the local LAN are forwarded to the LAN; other packets are discarded.

The default operation is used when the Default Gateway field is blank.

D-14 Quick Setup Menu

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Page 69 Page 71
Image 70
Page 69 Page 71
Contents RIC-E1 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 RIC-E1 International Headquarters RAD Data Communications IncLimited Warranty General Safety Instructions Please observe the following precautionsConnection of AC Mains General Safety PracticesConnection of DC Mains Ports Safety Status IsdnElectromagnetic Compatibility EMC Canadian Emission Requirements Product Names SafetyManufacturers Name Manufacturers Address Supplementary InformationJumper Description Values Default Setting Installing RIC-E1Setting the Internal Jumpers Quick Start GuideOperating RIC-E1 Connecting the CablesTo connect cables Contents List of Figures Overview Power SupplyChapter Introduction VersionsPhysical Description ApplicationFunctional Description Functional Block DiagramDiagnostics Timing ReferenceDerived from three alternative sources Technical SpecificationsReceive, derived from the received signal Internal oscillatorPhysical DiagnosticsPower EnvironmentTechnical Specifications Package Contents Chapter Installation and SetupSite Requirements and Prerequisites To install RIC-E1 Configuring RIC-E1Setting the Jumpers To set the jumpersRIC-E1 Jumper Locations RIC-E1 Jumper Settings Selecting the Impedance Connecting the InterfacesConnecting the E1 Line Closing the RIC-E1 CaseConnecting the AC Power Connecting the PowerConnecting the DTE Connecting the DC PowerInstallation and Setup Chapter Operation Front Panel IndicatorsDesignation Color Function Operating RIC-E1 Operating InstructionsTurning On Turning OffPerforming Local Analog Loopback Chapter Troubleshooting DiagnosticsActivating Local Analog Loopback Deactivating Local Analog Loopback TroubleshootingRIC-E1 Troubleshooting To activate the local analog loopback from RIC-E1/RTechnical Support Technical Support Chapter RIC-E1/R Card Line ConnectorDTE Connector ASM-MN-214 Card CageASM-MN-214 Rear Panel AC Supply Power SupplyPower Supply with Redundancy DC SupplyRIC-E1/R Front Panel IR-ETH or IR-ETHASM-MN-214 Front Panel Setting Internal Jumpers and Switches Installing the RIC-E1/R CardRIC-E1/R PCB Layout RIC-E1/R Jumper Settings Installing RIC-E1/R into the ASM-MN-214 Card Cage To install the RIC-E1/R card in the ASM-MN-214 card cageRIC-E1/R Card Appendix a Interface Connector Wiring V.35, X.21 and RS-530 Interface ConnectorsV.36 Interface Connector Signal Function 36, 37-Pin RS-530, 25-pin CircuitSignal Function 36, 37-pin RS-530, 25-pin Pin Circuit Line Interface ConnectorTable A-3. RJ-45 Line Interface Connector, Pin Assignment Pin FunctionAppendix a Interface Connector Wiring Appendix B IR-ETH Interface Module ContentsIntroduction RIC-E1/R Card IR-ETH OptionsStandalone RIC-E1 Table B-1. RJ-45 PinoutFigure B-3. RIC-E1/R with IR-ETH Installation and Operation LED Indicators Setting the DIP SwitchTable B-2. DIP Switch Settings Link Connecting the LANTable B-4. IR-ETH LED Indicators, RIC-E1/R ACTAppendix C IR-ETH/V Interface Module IR-ETH/V Options RIC-E1 Throughput For example, MDI in OFF position, MDI is enabledMbps full duplex, 285 ∝s Data 00, 01, 02, …Moved by the user Table C-3. DIP Switch SW2 Settings Setting the DIP SwitchesTable C-2. DIP SW1 Switch Settings Section Name Description Possible Settings Factory SettingBackpressure and Flow Control Table C-4. IR-ETH/V LED IndicatorsColor Function Appendix D IR-IP Interface Module IntroductionAppendix D IR-IP Interface Module Protocols Connector 10BaseT Shielded RJ-45Standard Ieee 802.3/Ethernet Data Rate Frame Relay RFCRIC-E1/ IP Table D-1. IR-IP LEDs Functions Standalone RIC-E1 IR-IP LEDsIR-IP Controls Table D-2. IR-IP LEDs Functions RIC-E1/R CardTable D-3. IR-IP Controls Control Function Values Default SettingIR-IP Management Subsystem, General Table D-4 RJ-45 PinoutAccessing the IR-IP Management Subsystem Default IP Communication ParametersOutline of Preliminary Configuration Performing Preliminary ConfigurationRescue Configuration To allow the IR-IP configurationAssigning the Router LAN Interface Address Connecting the Telnet HostPreliminary Telnet Host Configuration IP Learning MechanismTo configure the IP router LAN address To view and edit the ARP table contentsAssigning a LAN IP Address to a New IR-IP What to Do If Changing the LAN IP Address of a Configured IR-IPAfter RIC-E1 is turned on, the ERR indicator does not light No ping replies from IR-IPIR-IP Management Utility General Operating ProceduresStarting a Management Utility To access the Quick Setup menu Quick Setup MenuMenu Structure of Management Utility LAN IP Mask Default GatewayLAN IP Address WAN IP AddressTo configure the IR-IP as a Dhcp relay Read Protocol from DIP SwitchesOperation with Default Gateway Dhcp RelayTo access the Management Access menu Management Access MenuTelnet Password ProtocolTo access the Advanced Setup menu Advanced Setup MenuTelnet Inactivity Timeout To access the Device Identification menuDevice Name To access the Interface Parameters menuInterface Parameters Menu Contact PersonWAN Protocol Parameters Frame Relay Protocol Menu Header and Control Field Compression Authentication ProtocolWAN Protocol Parameters PPP Protocol Protocol Field CompressionMulticast IP Multicast Forwarding Figure D-17. Multicast IP MenuDevice Control To access the Device Control menuStatic Groups Viewing Error Log Screen New Software Download MenuResetting the Device Erasing ConfigurationResets Menu Resetting the LAN InterfaceTo access the Configuration and Connection screen Configuration and ConnectionTo access the View menu View MenuTo access the ARP Tables screen ARP TablesMulticast Groups Table Screen To access the Multicast Groups Table screenTo access the Statistics menu Displaying StatisticsDiagnostic Tools Ping Terminal To access the Diagnostic Tools menuUsing the Ping Function To ping a hostErasing IR-IP Software Erasing User’s ConfigurationTo erase the user’s configuration Desired positions, and then turn the RIC-E1 on againTo erase the application software Erasing Application SoftwareDownloading New Software Case, it is recommended to turn RIC-E1 off and then back onAppendix D IR-IP Interface Module Appendix E IR-X.21B Interface Module Rear PanelEXT Clock Mode Selecting the IR-X.21B TimingIR-X.21B INT/LBT Clock ModeBuffer Appendix E IR-X.21B Interface Module IP-IR Impedance, 2-4IndicatorsIndex IR-ETHLED IR-IPRequirements, 2-1RIC-E1/R Card Customer Response Form Excellent Good Fair Poor Very PoorError Report Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 International Headquarters
Top Page Image Contents