Appendix D IR-IP Interface Module | RIC-E1Installation and Operation Manual |
| |
New Software Download Menu
IR-IP operates as a TFTP client, and therefore it is possible to update its software by downloading new software from another computer that operates as a TFTP server.
The New Software Download menu is used to specify the software downloading parameters.
To access the New Software Download menu:
•From the Device Control submenu, type 1.
New Software Download menu appears (Figure D-20).
IR_IP<IR-IP>S/W Ver. 1.21 31/IR (date)
Quick Setup Management Access Advanced Setup Device Control
.....................................................................
New Software Download
=====================================================================
1. | Server IP Address | : |
2. | File Name | : |
3. | Total Timeout (sec) | :.. |
4. | Start operation | :>>> |
Press one of the numbers to select or ESC:
Figure D-20. New Software Download Menu
Server IP Address
Used to enter the IP address of the TFTP server.
File Name
Used to enter the name and path of the file to be transferred from the TFTP server.
Total Timeout
Used to enter the time IP router should wait for an acknowledgment from the TFTP server, for example 60 seconds.
Start Operation
After selecting all the necessary parameters, type 4 on the New Software Download screen and then press <Enter> to start the downloading.
You can follow the progress of the downloading process (indicated by arrows).
Upon completion of the download process, the unit performs a reset. The Telnet connection is lost and must be restarted if required.
Viewing Error Log Screen
This item of the Device Control submenu is used to view the error log file. This file logs errors detected in IR-IP for debug and technical support purposes.
D-24 Device Control
Order from: Cutter Networks | Ph:727-398-5252/Fax:727-397-9610 | www.bestdatasource.com |
RIC-E1
Order from Cutter Networks Ph727-398-5252/Fax727-397-9610
RIC-E1
International Headquarters RAD Data Communications Inc
Limited Warranty
General Safety Instructions
Please observe the following precautions
Connection of DC Mains
General Safety Practices
Connection of AC Mains
Ports Safety Status
Isdn
Electromagnetic Compatibility EMC
Canadian Emission Requirements
Safety
Manufacturers Name Manufacturers Address
Product Names
Supplementary Information
Installing RIC-E1
Setting the Internal Jumpers
Jumper Description Values Default Setting
Quick Start Guide
To connect cables
Connecting the Cables
Operating RIC-E1
Contents
List of Figures
Power Supply
Chapter Introduction
Overview
Versions
Physical Description
Application
Functional Block Diagram
Diagnostics
Functional Description
Timing Reference
Technical Specifications
Receive, derived from the received signal
Derived from three alternative sources
Internal oscillator
Diagnostics
Power
Physical
Environment
Technical Specifications
Site Requirements and Prerequisites
Chapter Installation and Setup
Package Contents
Configuring RIC-E1
Setting the Jumpers
To install RIC-E1
To set the jumpers
RIC-E1 Jumper Locations RIC-E1 Jumper Settings
Connecting the Interfaces
Connecting the E1 Line
Selecting the Impedance
Closing the RIC-E1 Case
Connecting the Power
Connecting the DTE
Connecting the AC Power
Connecting the DC Power
Installation and Setup
Designation Color Function
Front Panel Indicators
Chapter Operation
Operating Instructions
Turning On
Operating RIC-E1
Turning Off
Activating Local Analog Loopback
Chapter Troubleshooting Diagnostics
Performing Local Analog Loopback
Troubleshooting
RIC-E1 Troubleshooting
Deactivating Local Analog Loopback
To activate the local analog loopback from RIC-E1/R
Technical Support
Technical Support
Line Connector
DTE Connector
Chapter RIC-E1/R Card
ASM-MN-214 Card Cage
ASM-MN-214 Rear Panel
Power Supply
Power Supply with Redundancy
AC Supply
DC Supply
RIC-E1/R Front Panel
IR-ETH or IR-ETH
ASM-MN-214 Front Panel
RIC-E1/R PCB Layout RIC-E1/R Jumper Settings
Installing the RIC-E1/R Card
Setting Internal Jumpers and Switches
Installing RIC-E1/R into the ASM-MN-214 Card Cage
To install the RIC-E1/R card in the ASM-MN-214 card cage
RIC-E1/R Card
Appendix a Interface Connector Wiring
V.35, X.21 and RS-530 Interface Connectors
V.36 Interface Connector
Signal Function 36, 37-Pin RS-530, 25-pin Circuit
Line Interface Connector
Table A-3. RJ-45 Line Interface Connector, Pin Assignment
Signal Function 36, 37-pin RS-530, 25-pin Pin Circuit
Pin Function
Appendix a Interface Connector Wiring
Introduction
Contents
Appendix B IR-ETH Interface Module
IR-ETH Options
Standalone RIC-E1
RIC-E1/R Card
Table B-1. RJ-45 Pinout
Figure B-3. RIC-E1/R with IR-ETH
Installation and Operation
Table B-2. DIP Switch Settings
Setting the DIP Switch
LED Indicators
Connecting the LAN
Table B-4. IR-ETH LED Indicators, RIC-E1/R
Link
ACT
Appendix C IR-ETH/V Interface Module
IR-ETH/V Options
RIC-E1
For example, MDI in OFF position, MDI is enabled
Mbps full duplex, 285 ∝s
Throughput
Data 00, 01, 02, …
Setting the DIP Switches
Table C-2. DIP SW1 Switch Settings
Moved by the user Table C-3. DIP Switch SW2 Settings
Section Name Description Possible Settings Factory Setting
Color Function
Table C-4. IR-ETH/V LED Indicators
Backpressure and Flow Control
Appendix D IR-IP Interface Module
Introduction
Appendix D IR-IP Interface Module
Connector 10BaseT Shielded RJ-45
Standard Ieee 802.3/Ethernet Data Rate
Protocols
Frame Relay RFC
RIC-E1/ IP
IR-IP LEDs
IR-IP Controls
Table D-1. IR-IP LEDs Functions Standalone RIC-E1
Table D-2. IR-IP LEDs Functions RIC-E1/R Card
Control Function Values Default Setting
IR-IP Management Subsystem, General
Table D-3. IR-IP Controls
Table D-4 RJ-45 Pinout
Accessing the IR-IP Management Subsystem
Default IP Communication Parameters
Performing Preliminary Configuration
Rescue Configuration
Outline of Preliminary Configuration
To allow the IR-IP configuration
Connecting the Telnet Host
Preliminary Telnet Host Configuration
Assigning the Router LAN Interface Address
IP Learning Mechanism
Assigning a LAN IP Address to a New IR-IP
To view and edit the ARP table contents
To configure the IP router LAN address
Changing the LAN IP Address of a Configured IR-IP
After RIC-E1 is turned on, the ERR indicator does not light
What to Do If
No ping replies from IR-IP
Starting a Management Utility
General Operating Procedures
IR-IP Management Utility
Menu Structure of Management Utility
Quick Setup Menu
To access the Quick Setup menu
Default Gateway
LAN IP Address
LAN IP Mask
WAN IP Address
Read Protocol from DIP Switches
Operation with Default Gateway
To configure the IR-IP as a Dhcp relay
Dhcp Relay
Management Access Menu
Telnet Password
To access the Management Access menu
Protocol
Advanced Setup Menu
Telnet Inactivity Timeout
To access the Advanced Setup menu
To access the Device Identification menu
To access the Interface Parameters menu
Interface Parameters Menu
Device Name
Contact Person
WAN Protocol Parameters Frame Relay Protocol Menu
Authentication Protocol
WAN Protocol Parameters PPP Protocol
Header and Control Field Compression
Protocol Field Compression
Multicast IP
Multicast Forwarding
Figure D-17. Multicast IP Menu
Static Groups
To access the Device Control menu
Device Control
Viewing Error Log Screen
New Software Download Menu
Erasing Configuration
Resets Menu
Resetting the Device
Resetting the LAN Interface
Configuration and Connection
To access the View menu
To access the Configuration and Connection screen
View Menu
To access the ARP Tables screen
ARP Tables
To access the Multicast Groups Table screen
To access the Statistics menu
Multicast Groups Table Screen
Displaying Statistics
Diagnostic Tools Ping Terminal
To access the Diagnostic Tools menu
Using the Ping Function
To ping a host
Erasing User’s Configuration
To erase the user’s configuration
Erasing IR-IP Software
Desired positions, and then turn the RIC-E1 on again
Erasing Application Software
Downloading New Software
To erase the application software
Case, it is recommended to turn RIC-E1 off and then back on
Appendix D IR-IP Interface Module
Appendix E IR-X.21B Interface Module
Rear Panel
EXT Clock Mode
Selecting the IR-X.21B Timing
Buffer
INT/LBT Clock Mode
IR-X.21B
Appendix E IR-X.21B Interface Module
Impedance, 2-4Indicators
Index
IP-IR
IR-ETH
Requirements, 2-1RIC-E1/R Card
IR-IP
LED
Customer Response Form
Excellent Good Fair Poor Very Poor
Error Report
Order from Cutter Networks Ph727-398-5252/Fax727-397-9610
International Headquarters