Cisco Systems 11.0 BT manual Generic-pool

Page 22

generic-pool

generic-pool

Use the generic-poolTN3270 configuration command to specify whether or not left over LUs will be made available to TN3270 sessions that do not request a specific LU or LU pool through TN3270E. Use the no form of this command to selectively remove the permit or deny condition of generic pool use.

generic-pool {permit deny} no generic-pool

Syntax Description

 

permit

Left over LUs should be made available to TN3270 users

 

wanting generic sessions. This value is the default.

deny

Left over LUs should not be given to a generic pool. The

 

physical unit (PU) is not automatically fully populated with

 

255 LOCADDR definitions. The default is the value

 

configured in TN3270 configuration mode.

Defaults

In TN3270 configuration mode, generic pool use is permitted.

In PU configuration mode, the default is the value currently configured in TN3270 configuration mode.

Command Modes

TN3270 configuration

PU configuration

Usage Guidelines

A left over LU is defined as one for which all of the following conditions are true:

The system services control point (SSCP) did not send an ACTLU during PU start up; and

The PU controlling the LU is capable of carrying product set ID (PSID) vectors on network management vector transport (NMVT) messages, thus allowing dynamic definition of dependent LU (DDDLU) operation for that LU.

All LUs in the generic pool are, by definition, DDDLU capable.

Values entered for generic-poolin TN3270 configuration mode apply to all PUs for that TN3270 server but can be changed in PU configuration mode.

In PU configuration mode, a no generic-poolcommand will restore the generic-poolvalue entered in TN3270 command mode.

In TN3270 configuration mode, the no generic-poolcommand reverts to the default, which permits generic pool use.

The command takes effect immediately. If generic-pool deny is specified on a PU, no further dynamic connections to it will be allowed. Existing sessions are unaffected, but, as they terminate, the LUs will not become available for dynamic connections.

22TN3270 Server Commands

Image 22
Contents January 15 Release Note IntroductionIntroduction Platform Support Boot ROM RequirementsCIP Boot Image Requirements Cisco IOS PackagingUpdate to Configuration Guide Microcode Software New Software Features in 11.010BTConfiguring TN3270 Server on the Channel Interface Processor Dynamic LU Allocation Configuring TN3270 on a Channel Interface ProcessorConfiguring TN3270 on a Channel Interface Processor Formation of LU Model Type and NumberExamples of Model String Mapping Specific LU AllocationString from client Ascii Requested? String to Host Ebcdic Direct PU Configuration in Router Adapte Comman Name SNA Session Switch-End Node DlurMultiple Hosts Support IP-address Type NumberIDBLK=05D Task Command TN3270 Configuration ModesTN3270 Configuration Modes TN3270 Server Configuration Mode Dlur Configuration ModePU Configuration Mode Dlur SAP Configuration ModeCommands Allowed in Multiple Modes Task List for Multiple Appn Hosts TN3270 Configuration Task ListTN3270 Configuration Task List Task List for Non-APPN HostsConfigure TN3270 Server Configure PU Parameters on the TN3270 ServerConfigure Dlur TN3270 Configuration Task List CommandConfigure SAPs under Dlur Monitor the TN3270 Server Configure PUs under DlurPu pu-name idblk-idnum ip-address TN3270 Configuration Example Configuration dialog to configure the TN3270 function followsSYD.TN3020 SYD.VMG Update to Command Reference Update to Command ReferenceDlur DlurDlus-backup Dlus-backupGeneric-pool Generic-poolFollowing command permits generic LU pool use Idle-time Idle-timeKeepalive KeepaliveLink LinkLsap token-adapter Link Host rmac 4000.0000.0001 rsap Internal adapter type on the CIP card, which corresponds to LsapLsap 4. It must be unique within the internal adapter in that noRelated Commands Maximum-lus Maximum-lusPreferred-nnserver Preferred-nnserverHosts are in which domains and does not enforce the unique Pu directPu direct PUs may use the same value on the internal adapter as longDefaults When a specific LU name request is needed. The format can34 TN3270 Server Commands Pu Dlur Pu DlurThis value must match the idblk-idnum value defined at Show tn3270-server Field Descriptions Show extended channel tn3270-serverShow extended channel tn3270-server LU numberDlur fq-cpname Fail numberNumber Dlus fq-dlusname38 TN3270 Server Commands Show extended channel tn3270-server client-ip-address Show extended channel tn3270-server client-ip-addressLU lu-name Show tn3270-server client-ip-address Field DescriptionsLU locaddr Ip-addrtcpport State lu-stateNumber/number Show extended channel tn3270-server dlur Show extended channel tn3270-server dlurShow tn3270-server dlur Field Descriptions VRN fq-name Show tn3270-server dlurlink Field Descriptions Show extended channel tn3270-server dlurlinkShow extended channel tn3270-server dlurlink TGN tg-numberShow extended channel tn3270-server pu Show extended channel tn3270-server puShow tn3270-server pu Field Descriptions State pu-stateLU states and their meanings are Show extended channel tn3270-server pu lu Show extended channel tn3270-server pu luShow tn3270-server pu lu Field Descriptions 50 TN3270 Server Commands Shutdown ShutdownTcp-port Tcp-portTiming-mark Timing-markTn3270-server Tn3270-serverUnbind-action Unbind-actionVrn VrnCisco Connection Documentation Cisco Connection OnlineCisco Connection Online Cisco Connection Documentation