Cisco Systems 11.0 BT manual Show extended channel tn3270-server dlurlink, TGN tg-number

Page 44

show extended channel tn3270-server dlurlink

show extended channel tn3270-server dlurlink

Use the show extended channel tn3270-server dlurlink privileged EXEC command to display information about the DLUR components.

show extended channel slot/2 tn3270-server dlurlink name

Syntax Description

 

slot/2

Specifies a particular CIP in the router where slot is the slot number.

 

The port value for a TN3270 server will always be 2.

name

Name of the SNA session switch link to be displayed.

Command Mode

 

Privileged EXEC

 

Sample Display

The following is sample output on the Cisco 7000 from the show extended channel tn3270-server dlurlink command:

router# show extended channel 3/2 tn3270-server dlurlink P390

lsap

token-adapter

0 5C vrn MPX.LAN4

status ACTIVE

link

P390

remote 4000.7470.00e7 08

status ACTIVE

partner MPX.NGMVMPC

tgn 1

maxdata 1033

Table 8 describes significant fields in the display.

Table 8 Show tn3270-server dlurlink Field Descriptions

Field

Description

LSAP...VRN...STATUS status

Possible sap-statusvalues and their meanings are:

 

inactive—Not connected to adapter.

 

pnd-actv—SAP activation in progress.

 

active—SAP open.

 

pnd-inac—SAP deactivation in progress.

 

 

LINK name

Name is an invented name, @DLURnn, if not a configured link.

 

 

LINK...STATUS status

Possible link-statusvalues and their meanings are:

 

inactive—Not connected to host.

 

pnd-actv—Link activation in progress.

 

active—Link active.

 

pnd-inac—Link deactivation in progress.

 

 

PARTNER name

CP name of the remote node for this link.

 

 

TGN tg-number

Transmission group number for this link. Because the SNA session

 

switch only supports 1 transmission group per pair of CP names, it

 

is typically 0 or 1.

 

 

MAXDATA maxdata

Maximum frame size allowed on this link.

 

 

 

44TN3270 Server Commands

Image 44
Contents January 15 Introduction IntroductionRelease Note Boot ROM Requirements CIP Boot Image RequirementsPlatform Support Cisco IOS PackagingUpdate to Configuration Guide Microcode Software New Software Features in 11.010BTConfiguring TN3270 Server on the Channel Interface Processor Configuring TN3270 on a Channel Interface Processor Configuring TN3270 on a Channel Interface ProcessorDynamic LU Allocation Formation of LU Model Type and NumberString from client Ascii Requested? String to Host Ebcdic Specific LU AllocationExamples of Model String Mapping SNA Session Switch-End Node Dlur Multiple Hosts SupportDirect PU Configuration in Router Adapte Comman Name IP-address Type NumberIDBLK=05D TN3270 Configuration Modes TN3270 Configuration ModesTask Command TN3270 Server Configuration Mode Dlur Configuration ModeCommands Allowed in Multiple Modes Dlur SAP Configuration ModePU Configuration Mode TN3270 Configuration Task List TN3270 Configuration Task ListTask List for Multiple Appn Hosts Task List for Non-APPN HostsConfigure TN3270 Server Configure PU Parameters on the TN3270 ServerConfigure SAPs under Dlur TN3270 Configuration Task List CommandConfigure Dlur Pu pu-name idblk-idnum ip-address Configure PUs under DlurMonitor the TN3270 Server TN3270 Configuration Example Configuration dialog to configure the TN3270 function followsSYD.TN3020 SYD.VMG Update to Command Reference Update to Command ReferenceDlur DlurDlus-backup Dlus-backupGeneric-pool Generic-poolFollowing command permits generic LU pool use Idle-time Idle-timeKeepalive KeepaliveLink LinkLsap token-adapter Link Host rmac 4000.0000.0001 rsap Lsap LsapInternal adapter type on the CIP card, which corresponds to 4. It must be unique within the internal adapter in that noRelated Commands Maximum-lus Maximum-lusPreferred-nnserver Preferred-nnserverPu direct Pu directHosts are in which domains and does not enforce the unique PUs may use the same value on the internal adapter as longDefaults When a specific LU name request is needed. The format can34 TN3270 Server Commands This value must match the idblk-idnum value defined at Pu DlurPu Dlur Show extended channel tn3270-server Show extended channel tn3270-serverShow tn3270-server Field Descriptions LU numberFail number NumberDlur fq-cpname Dlus fq-dlusname38 TN3270 Server Commands Show extended channel tn3270-server client-ip-address Show extended channel tn3270-server client-ip-addressShow tn3270-server client-ip-address Field Descriptions LU locaddrLU lu-name Ip-addrtcpport State lu-stateNumber/number Show tn3270-server dlur Field Descriptions Show extended channel tn3270-server dlurShow extended channel tn3270-server dlur VRN fq-name Show extended channel tn3270-server dlurlink Show extended channel tn3270-server dlurlinkShow tn3270-server dlurlink Field Descriptions TGN tg-numberShow extended channel tn3270-server pu Show extended channel tn3270-server puShow tn3270-server pu Field Descriptions State pu-stateLU states and their meanings are Show extended channel tn3270-server pu lu Show extended channel tn3270-server pu luShow tn3270-server pu lu Field Descriptions 50 TN3270 Server Commands Shutdown ShutdownTcp-port Tcp-portTiming-mark Timing-markTn3270-server Tn3270-serverUnbind-action Unbind-actionVrn VrnCisco Connection Online Cisco Connection OnlineCisco Connection Documentation Cisco Connection Documentation