Cisco Systems 11.0 BT Show extended channel tn3270-server, Show tn3270-server Field Descriptions

Page 36

show extended channel tn3270-server

show extended channel tn3270-server

Use the show extended channel tn3270-serverprivileged EXEC command to display current server conﬁguration parameters and the status of the PUs deﬁned in each TN3270 server.

show extended channel slot/2 tn3270-server

Syntax Description
slot/2	Speciﬁes a particular CIP in the router where slot is the slot number.
	The port value for a TN3270 server is always 2.
Command Mode
Privileged EXEC

Sample Display

The following is sample output on the Cisco 7000 from the show extended channel tn3270-servercommand:

router# show extended channel 3/2 tn3270-server

<current stats> < connection stats >				<response time(ms)>
server-ip:tcp	lu in-use		connect disconn fail			host	tcp
172.28.1.106:23	510	1	12	11	0	54	40
172.28.1.107:23	511	0	0	0	0	0	0
172.28.1.108:23	255	0	0	0	0	0	0
total	1276	1

configured max_lu 20000
idle-time		0	keepalive 1800		unbind-action disconnect
tcp-port	23		generic-pool permit no timing-mark
dlur MPX.GOANCP					status NOTQRYD		SHUT
dlus MPX.NGMVMPC
name(index)		ip:tcp		xid	state	link	destination	r-lsap
EXT2(1)		172.28.1.106:23		05D18092	ACTIVE	tok 0	4000.7470.00e7 08 04
PUS10(2)		172.28.1.107:23		05D19010	ACTIVE	tok 0	4000.7470.00e7 08 2C
PUS11(3)		172.28.1.107:23		05D19011	ACTIVE	tok 0	4000.7470.00e7 08 28
PUS12(4)		172.28.1.108:23		05D19012	ACTIVE	tok 0	4000.7470.00e7 08 24
PUS9(5)		172.28.1.109:23		05D18509	SHUT	tok 0	4001.3745.1088 04 40
SDTF(7)		172.28.1.107:23		12345678	ACTIVE	tok 0	0800.5a4b.1cbc 04 08
TEST(8)		172.28.1.106:23		05D18091	ACTIVE	tok 0	4000.7470.00e7 08 30
INT1(6)		172.28.1.106:23		05D18091	SHUT	dlur

Table 5 describes signiﬁcant ﬁelds in the display. Those ﬁelds not described correspond to conﬁgured values.

Table 5 Show tn3270-server Field Descriptions

	Field	Description
	SERVER-IP:TCP	IP address and TCP port number, listening point, conﬁgured on one
		or more PUs.

	LU number	Total number of LUs available for this listening point.

	IN-USE number	Number of LUs currently in use.

	CONNECT number	Total number of connect ins since the TN3270 feature was started.

36 TN3270 Server Commands

Image 36

Contents January 15 Introduction Release NoteIntroduction Boot ROM Requirements CIP Boot Image RequirementsPlatform Support Cisco IOS PackagingUpdate to Conﬁguration Guide Microcode Software New Software Features in 11.010BTConﬁguring TN3270 Server on the Channel Interface Processor Configuring TN3270 on a Channel Interface Processor Conﬁguring TN3270 on a Channel Interface ProcessorDynamic LU Allocation Formation of LU Model Type and NumberSpeciﬁc LU Allocation Examples of Model String MappingString from client Ascii Requested? String to Host Ebcdic SNA Session Switch-End Node Dlur Multiple Hosts SupportDirect PU Conﬁguration in Router Adapte Comman Name IP-address Type NumberIDBLK=05D TN3270 Configuration Modes Task CommandTN3270 Conﬁguration Modes TN3270 Server Conﬁguration Mode Dlur Conﬁguration ModeDlur SAP Conﬁguration Mode PU Conﬁguration ModeCommands Allowed in Multiple Modes TN3270 Configuration Task List TN3270 Conﬁguration Task ListTask List for Multiple Appn Hosts Task List for Non-APPN HostsConﬁgure TN3270 Server Conﬁgure PU Parameters on the TN3270 ServerTN3270 Configuration Task List Command Conﬁgure DlurConﬁgure SAPs under Dlur Conﬁgure PUs under Dlur Monitor the TN3270 ServerPu pu-name idblk-idnum ip-address TN3270 Conﬁguration Example Conﬁguration dialog to conﬁgure the TN3270 function followsSYD.TN3020 SYD.VMG Update to Command Reference Update to Command ReferenceDlur DlurDlus-backup Dlus-backupGeneric-pool Generic-poolFollowing command permits generic LU pool use Idle-time Idle-timeKeepalive KeepaliveLink LinkLsap token-adapter Link Host rmac 4000.0000.0001 rsap Lsap LsapInternal adapter type on the CIP card, which corresponds to 4. It must be unique within the internal adapter in that noRelated Commands Maximum-lus Maximum-lusPreferred-nnserver Preferred-nnserverPu direct Pu directHosts are in which domains and does not enforce the unique PUs may use the same value on the internal adapter as longDefaults When a speciﬁc LU name request is needed. The format can34 TN3270 Server Commands Pu Dlur Pu DlurThis value must match the idblk-idnum value deﬁned at Show extended channel tn3270-server Show extended channel tn3270-serverShow tn3270-server Field Descriptions LU numberFail number NumberDlur fq-cpname Dlus fq-dlusname38 TN3270 Server Commands Show extended channel tn3270-server client-ip-address Show extended channel tn3270-server client-ip-addressShow tn3270-server client-ip-address Field Descriptions LU locaddrLU lu-name Ip-addrtcpport State lu-stateNumber/number Show extended channel tn3270-server dlur Show extended channel tn3270-server dlurShow tn3270-server dlur Field Descriptions VRN fq-name Show extended channel tn3270-server dlurlink Show extended channel tn3270-server dlurlinkShow tn3270-server dlurlink Field Descriptions TGN tg-numberShow extended channel tn3270-server pu Show extended channel tn3270-server puShow tn3270-server pu Field Descriptions State pu-stateLU states and their meanings are Show extended channel tn3270-server pu lu Show extended channel tn3270-server pu luShow tn3270-server pu lu Field Descriptions 50 TN3270 Server Commands Shutdown ShutdownTcp-port Tcp-portTiming-mark Timing-markTn3270-server Tn3270-serverUnbind-action Unbind-actionVrn VrnCisco Connection Online Cisco Connection DocumentationCisco Connection Online Cisco Connection Documentation