Cisco Systems 11.0 BT manual Keepalive

Page 25

keepalive

keepalive

Use the keepalive TN3270 configuration command to specify how many seconds of inactivity elapse before transmission of a DO TIMING-MARK to the TN3270 client. Use the no form of this command to cancel the keepalive period and return to the default.

keepalive seconds no keepalive

Syntax Description

 

seconds

Number of seconds, from 0 to 65535. A value of 0 means

 

no keepalive signals are sent. The default is 1800 seconds

 

(30 minutes).

Defaults

The default in TN3270 configuration mode is 1800 seconds (30 minutes).

The default in PU configuration mode is the value currently configured in TN3270 configuration mode.

Command Modes

TN3270 configuration

PU configuration

Usage Guidelines

The keepalive command can be entered in either TN3270 configuration mode or PU configuration mode. A value entered in TN3270 mode applies to all PUs for that TN3270 server, except as overridden by values entered in PU configuration mode. A no keepalive command entered in PU configuration mode will restore the keepalive value entered in TN3270 command mode.

If the client does not reply within 30 minutes of the transmission of the DO TIMING-MARK, the TN3270 server disconnects the TN3270 session. The DO TIMING-MARK is a Telnet protocol operation that does not affect the client operation.

If the IP path to the client is broken, the TCP layer will detect the failure to acknowledge the DO TIMING-MARK and initiate disconnection. This action will usually take much less than 30 minutes.

The keepalive command affects currently active and future TN3270 sessions. For example, reducing the value to a smaller nonzero value will cause an immediate burst of DO TIMING-MARKs on those sessions that have been inactive for a period of time greater than the new, smaller value.

Examples

The following command sets a keepalive disconnect value of 15 minutes (900 seconds):

keepalive 900

The following command entered in TN3270 configuration mode sets the keepalive disconnect value to 1800 seconds, the default:

no keepalive

TN3270 Server Commands 25

Image 25
Contents January 15 Release Note IntroductionIntroduction CIP Boot Image Requirements Boot ROM RequirementsPlatform Support Cisco IOS PackagingMicrocode Software New Software Features in 11.010BT Update to Configuration GuideConfiguring TN3270 Server on the Channel Interface Processor Configuring TN3270 on a Channel Interface Processor Configuring TN3270 on a Channel Interface ProcessorDynamic LU Allocation Formation of LU Model Type and NumberExamples of Model String Mapping Specific LU AllocationString from client Ascii Requested? String to Host Ebcdic Multiple Hosts Support SNA Session Switch-End Node DlurDirect PU Configuration in Router Adapte Comman Name IP-address Type NumberIDBLK=05D Task Command TN3270 Configuration ModesTN3270 Configuration Modes Dlur Configuration Mode TN3270 Server Configuration ModePU Configuration Mode Dlur SAP Configuration ModeCommands Allowed in Multiple Modes TN3270 Configuration Task List TN3270 Configuration Task ListTask List for Multiple Appn Hosts Task List for Non-APPN HostsConfigure PU Parameters on the TN3270 Server Configure TN3270 ServerConfigure Dlur TN3270 Configuration Task List CommandConfigure SAPs under Dlur Monitor the TN3270 Server Configure PUs under DlurPu pu-name idblk-idnum ip-address Configuration dialog to configure the TN3270 function follows TN3270 Configuration ExampleSYD.TN3020 SYD.VMG Update to Command Reference Update to Command ReferenceDlur DlurDlus-backup Dlus-backupGeneric-pool Generic-poolFollowing command permits generic LU pool use Idle-time Idle-timeKeepalive KeepaliveLink LinkLsap token-adapter Link Host rmac 4000.0000.0001 rsap Lsap LsapInternal adapter type on the CIP card, which corresponds to 4. It must be unique within the internal adapter in that noRelated Commands Maximum-lus Maximum-lusPreferred-nnserver Preferred-nnserverPu direct Pu directHosts are in which domains and does not enforce the unique PUs may use the same value on the internal adapter as longWhen a specific LU name request is needed. The format can Defaults34 TN3270 Server Commands Pu Dlur Pu DlurThis value must match the idblk-idnum value defined at Show extended channel tn3270-server Show extended channel tn3270-serverShow tn3270-server Field Descriptions LU numberNumber Fail numberDlur fq-cpname Dlus fq-dlusname38 TN3270 Server Commands Show extended channel tn3270-server client-ip-address Show extended channel tn3270-server client-ip-addressLU locaddr Show tn3270-server client-ip-address Field DescriptionsLU lu-name Ip-addrtcpport State lu-stateNumber/number Show extended channel tn3270-server dlur Show extended channel tn3270-server dlurShow tn3270-server dlur Field Descriptions VRN fq-name Show extended channel tn3270-server dlurlink Show extended channel tn3270-server dlurlinkShow tn3270-server dlurlink Field Descriptions TGN tg-numberShow extended channel tn3270-server pu Show extended channel tn3270-server puState pu-state Show tn3270-server pu Field DescriptionsLU states and their meanings are Show extended channel tn3270-server pu lu Show extended channel tn3270-server pu luShow tn3270-server pu lu Field Descriptions 50 TN3270 Server Commands Shutdown ShutdownTcp-port Tcp-portTiming-mark Timing-markTn3270-server Tn3270-serverUnbind-action Unbind-actionVrn VrnCisco Connection Documentation Cisco Connection OnlineCisco Connection Online Cisco Connection Documentation