Cisco Systems 11.0 BT manual Pu direct, Hosts are in which domains and does not enforce the unique

Page 32

pu (direct)

pu (direct)

Use the pu TN3270 configuration command to create a PU entity that has its own direct link to a host, or to enter PU configuration mode. Use the no form of this command to remove the PU entity.

pu pu-name

pu pu-name idblk-idnum ip-address type adapter-number lsap [rmac rmac] [rsap rsap] [lu-seedlu-name-stem]

no pu pu-name

Syntax Description

 

pu-name

Name that uniquely identifies this PU.

idblk-idnum

This value must match the IDBLK-IDNUM value defined

 

at the host. The value must be unique within the domain;

 

however, the TN3270 Server cannot tell which remote

 

hosts are in which domains and does not enforce the unique

 

value requirement.

ip-address

IP address that the clients should use as host IP address to

 

map to LU sessions under this PU.

type

Internal adapter type on the CIP card, which corresponds to

 

the value specified in the lan internal LAN configuration

 

command. The currently supported type is token-adapter.

adapter-number

Internal adapter interface on the CIP card, which is the

 

same value specified in the adapter internal LAN

 

configuration command.

lsap

Local SAP number in hexadecimal, ranging from 04 to FC.

 

The value must be even, and must be unique within the

 

internal adapter so that no other 802.2 clients of that

 

adapter, in the router or in a host, should be allocated the

 

same SAP. Other direct links from TN3270 server direct

 

PUs may use the same value on the internal adapter as long

 

as the remote MAC or SAP is different.

rmac rmac

(Optional) Remote MAC address. The remote MAC

 

address of the form xxxx.xxxx.xxxx hexadecimal, specifying

 

the MAC address of the remote host. If not specified, a

 

loopback link to another SAP on the same internal LAN

 

adapter is assumed.

rsap rsap

(Optional) Remote SAP address. The remote SAP address

 

is a one- or two-character hexadecimal string, ranging from

 

04 to FC, specifying the SAP address of the remote host.

 

The default is 04.

32TN3270 Server Commands

Image 32
Contents January 15 Introduction IntroductionRelease Note Boot ROM Requirements CIP Boot Image RequirementsPlatform Support Cisco IOS PackagingUpdate to Configuration Guide Microcode Software New Software Features in 11.010BTConfiguring TN3270 Server on the Channel Interface Processor Configuring TN3270 on a Channel Interface Processor Configuring TN3270 on a Channel Interface ProcessorDynamic LU Allocation Formation of LU Model Type and NumberString from client Ascii Requested? String to Host Ebcdic Specific LU AllocationExamples of Model String Mapping SNA Session Switch-End Node Dlur Multiple Hosts SupportDirect PU Configuration in Router Adapte Comman Name IP-address Type NumberIDBLK=05D TN3270 Configuration Modes TN3270 Configuration ModesTask Command TN3270 Server Configuration Mode Dlur Configuration ModeCommands Allowed in Multiple Modes Dlur SAP Configuration ModePU Configuration Mode TN3270 Configuration Task List TN3270 Configuration Task ListTask List for Multiple Appn Hosts Task List for Non-APPN HostsConfigure TN3270 Server Configure PU Parameters on the TN3270 ServerConfigure SAPs under Dlur TN3270 Configuration Task List CommandConfigure Dlur Pu pu-name idblk-idnum ip-address Configure PUs under DlurMonitor the TN3270 Server TN3270 Configuration Example Configuration dialog to configure the TN3270 function followsSYD.TN3020 SYD.VMG Update to Command Reference Update to Command ReferenceDlur DlurDlus-backup Dlus-backupGeneric-pool Generic-poolFollowing command permits generic LU pool use Idle-time Idle-timeKeepalive KeepaliveLink LinkLsap token-adapter Link Host rmac 4000.0000.0001 rsap Lsap LsapInternal adapter type on the CIP card, which corresponds to 4. It must be unique within the internal adapter in that noRelated Commands Maximum-lus Maximum-lusPreferred-nnserver Preferred-nnserverPu direct Pu directHosts are in which domains and does not enforce the unique PUs may use the same value on the internal adapter as longDefaults When a specific LU name request is needed. The format can34 TN3270 Server Commands This value must match the idblk-idnum value defined at Pu DlurPu Dlur Show extended channel tn3270-server Show extended channel tn3270-serverShow tn3270-server Field Descriptions LU numberFail number NumberDlur fq-cpname Dlus fq-dlusname38 TN3270 Server Commands Show extended channel tn3270-server client-ip-address Show extended channel tn3270-server client-ip-addressShow tn3270-server client-ip-address Field Descriptions LU locaddrLU lu-name Ip-addrtcpport State lu-stateNumber/number Show tn3270-server dlur Field Descriptions Show extended channel tn3270-server dlurShow extended channel tn3270-server dlur VRN fq-name Show extended channel tn3270-server dlurlink Show extended channel tn3270-server dlurlinkShow tn3270-server dlurlink Field Descriptions TGN tg-numberShow extended channel tn3270-server pu Show extended channel tn3270-server puShow tn3270-server pu Field Descriptions State pu-stateLU states and their meanings are Show extended channel tn3270-server pu lu Show extended channel tn3270-server pu luShow tn3270-server pu lu Field Descriptions 50 TN3270 Server Commands Shutdown ShutdownTcp-port Tcp-portTiming-mark Timing-markTn3270-server Tn3270-serverUnbind-action Unbind-actionVrn VrnCisco Connection Online Cisco Connection OnlineCisco Connection Documentation Cisco Connection Documentation