Bunn S/N SNG0033000 & UP manual Programming Switches

Page 12

PROGRAMMING

Using the menu-driven display on the front of the brewer, the operator has the ability to alter or modify various brewing parameters such as brew temperatures, brew volumes, bypass percentages, etc. This allows for the precise brewing of various flavors of coffee.

Programming of the brewer is achieved by entering a certain function. Then, by the use of hidden programming switches, the operator can customize the brewing process to their specifications.

PROGRAMMING SWITCHES

To access the programming mode, and to scroll through the different function screens, hidden programming switches are used. There are five of these switches that will be used for the setup of the brewer.

2

1

3 4 5

P2605

1.® symbol (upper right of the BUNN logo)

This is used to access the programming mode and is also used to scroll forward through the function list.

2.Upper left corner of the "B" in the BUNN logo

This is used to scroll backwards through the function list.

3."Digital" (lower left under the display)

This is used to select options that appear on the display during programming.

4."Brewer" (center under the display)

This is used to select options that appear on the display during programming.

5."Control" (lower right under the display)

This is used to select options that appear on the display during programming.

Page 12	35879.1 071405

Image 12

Contents Single TF DBC Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Table of Contents User Notices Volt ac single phase Hz models Electrical HOOK-UP37881.0002 Electrical Requirements Models without power cord 230 volt ac Single phase, 60 Hz modelsCE Requirements Plumbing RequirementsPlumbing HOOK-UP Main ON/OFF Switch Batch Selector SwitchesON/OFF Switch Enable Brew Brew SwitchInitial Setup Coffee BrewingCleaning Glossary Programming Switches ProgrammingProgramming Switch Program Functions Level RecipesDRIP-OUT Times Level Continues to DReturns to a Program Flow Diagram Return to aContinues to Programming the Brewer Units Setting Units of Measure Procedure for modifying units of measureProcedure for Setting the Recipe SET NEW RecipeThis function allows the operator to set Brew SET NEW Recipes Sizes DONE?Refer to SET Pulse Brew for description Procedure to program the coffee name Card Contains Recipe forReview RECIPES? Noyes Review RECIPES/MODIFY RECIPES/SET UP no Name Coffee Names Procedure for reviewing recipesNext To exit, press Next until the display reads ThatBrew OZ Setting or Adjusting Brew VOL- Umes ScreenBypass Review RecipesSET Pulse Brew Modifying pulse brew Range 1st on time off to 4 minutesNO-NAME Modifyshownext SET Pulse BrewSET Pulse Brew Easy Pulse Setup SET Pulse Brew Enter Times TIMES?DONE? SET Preinfusion Batches DONE?Setup Complete Enable ADS? Assign RecipesAssign Recipe ? SET Temp SET ReadyScreen Spray OZ/M Bypass OZ/M Calibrate FlowCalibrate Spray .. Press Brew to Start Procedures to calibrate the bypass flow rate Calibrate FlowStart Procedure to set funnel detect Procedures to view/reset the brew countersBrew Counters Funnel Detect optionalService Tools Testing individual components outputsProcedure to test components outputs Brew ValveNothing Pressed FrequencyFactory Defaults Procedure to set factory defaultsTroubleshooting Troubleshooting ProceduresScreen Displayed Possible CauseTemperature Press ON/OFF to terminate the cycleON/OFF switch was pressed after the brew cycle was started Press ON/OFF to terminate the brew cycleTank Heater failure Triac FailureTemperature Sensor Probe Wires shorted to housing, or toWater shut off to brewer Broken or not making connectionEquipment will not operate No power or incorrect voltage Brew switch Switch test proceduresBrew Valve Switch test procedures Data plate within +/- 10%Troubleshooting Problem Possible Cause Overflow Protection Switch When this condition occurs,With power removed from brewer Holding it in open state See above or boilingLimit Thermostat Heating Time TOO LongTroubleshooting Problem Inconsistent beverage level Strainer Server Pointing towards the brewerImproper water pressure 90 psi 138 and 620 kPaConsistently high or low beverage Brew Volume adjustment Water temperatureLevel in server For each brew cycleTroubleshooting Problem Possible Cause Weak beverage Remove and clean lime off tank heatersBrewer is making unusual noises Plumbing lines Water Supply Tank HeatersSchematic Wiring Diagram Single TF DBC Schematic Wiring Diagram Wire Single Phase Schematic Wiring Diagram Single TF DBC