NCR
manual
NCR S16 Minitower Server
Install
Configuring PCI Adapters
Documentation Needed for Setup
Confirming the Cmos Settings
How to
Power Management Mode
Rebooting the System
Enable 4 GB Support
Using an Adaptec Controller
Page 1
NCR S16 Minitower Server
Installing Network Operating System Release 3
BST0-2142-0100
12/97
Page 1
Page 2
Image 1
Page 1
Page 2
Contents
NCR S16 Minitower Server
Page
Contents
Installing Windows NT Server 4.0 Enterprise Edition
Installing SCO Unix
ViContents
About This Book
Preface
Who Should Read This Book
Related Publications
Conventions Used in This Book
Installation Overview
Overview
Documentation Needed for Setup
Step What to Do How to Do It Where to Find Information
Where to Start
Confirming the Cmos Settings and Configuring PCI Adapters
Confirming the Cmos Settings and Configuring PCI Adapters
Return to Page 1, and set parameters as follows
Confirming the Cmos Settings
ECC
Power Management Mode
Inta Intb Intc Intd
Configuring PCI Adapters
Configuring PCI Adapters
Configuring PCI Adapters
Confirming the Scsi Adapter Settings
Confirming the Scsi Adapter Settings
For Wide devices only
Configuring the Scsi Adapters
Configuring the Scsi Adapters Send Start Unit Command
Installing Microsoft Windows NT Server
Installing Microsoft Windows NT Server
Entering Windows Setup
Performing a Full Installation of Windows NT Server
Installing from the CD-ROM
Inserting the Windows NT Server Setup Disk
Preparing the Hard Disk
Performing a Full Installation of Windows NT Server
Performing a Full Installation of Windows NT Server
Continue
Completing User and Server Information
Selecting Network Protocols
Providing Additional Setup Information
Completing the Installation
Performing a Full Installation of Windows NT Server
Page
Installing Microsoft Windows NT Server
Overview
Starting the Pre-Loaded Installation
Pre-Loaded Installation
Entering the Setup Routine for NCR Server Manager
Completing the Pre-loaded Installation
Pre-Loaded Installation
Non-Pre-Load Installation
Performing a Full Installation of Windows NT Server
Preparing the Hard Disk
Performing a Full Installation of Windows NT Server
Installing the Network
Selecting Network Protocols
Entering Additional Setup Information
Installing Windows NT Server 4.0 Enterprise Edition
Action Reference
Install Service Pack
Boot.ini File Before Modification Example
Enable 4 GB Support
Boot.ini File After Modification Example
Enable 4 GB Support
Installing Netware
Installing Netware
Installation Overview
Rebooting the Server and Creating a Primary DOS Partition
Rebooting the Server and Creating a Primary DOS Partition
Loading the Controller’s Drivers
Using an Adaptec Controller
Loading the CD-ROM as a NetWare Volume
Installing NetWare
Choosing Drivers
Switching to the System Console Screen
Completing the Installation
Load Smcpwr SLOT=? FRAME=???? NAME=SMCPWR1E83
Installing NetWare
Installing SCO Unix
Installing SCO Unix
Installation Overview
Entering Setup Information
Rebooting the Server and Installing the Operating System
Inserting the CD-ROM
Inserting the Supplement Volume Disk
Rebooting the System
Inserting the Latest SMC Driver Disk
SCO Release 3 Installing TCP/IP Communications
Completing the Installation
Inserting the SMC SuperDisk
SCO Release 5 Installing TCP/IP Communications
Select Add Protocol. Observe the following
Installing UnixWare
Installing UnixWare
Installation Overview
Inserting the Host Bus Adapter HBA Driver
Observing Screen Messages
Selecting the Installation Method
Reinserting the Host Bus Adapter HBA Driver Disk
Entering a Password and Completing the Installation
Rebooting the Server and Installing the Operating System
Installing OS/2
10-2
Installation Overview
10-4
Editing CONFIG.SYS and Rebooting
Installing OS/2
Installing MP-RAS
Installing MP-RAS
Installation Overview
Default Installation Overview
Restarting the Installation
Booting from the Installation Media
Performing a Default Installation
Selecting the Type of Installation
Entering the System Name, Date, and Time
Selecting the Install Media Device
Specifying the Secondary Disk
Install Licenses Methods
Installing Licenses
Licenses, press a
11-12
Turning the System Off
Performing Additional Administrative Tasks
Shadow Options
Configuration Settings Required for Installing MP-RAS
Embedded Adaptec AIC-7880 Scsi Controller
Used Resources
11-18
Related pages
Troubleshooting for Samsung P2570
Specifications for JAMO R 907
Important Error Messages for Panasonic EB-X100
Wiring Diagram for Tektronix 1235
Why Integration is Important for Panasonic KX-TVS80
Getting ready to install the refrigerator for Samsung RSG257AABP
Model J-4200A Belt and Disc Sander Assembly Parts List for Jet Tools J-4301A
Language code list for Panasonic DVD-LX8
Limited Warranty for King Kutter TG-48-XB
How can I register my
Braun 5692 shaver
for warranty?
Top
Page
Image
Contents