NCR S16 manual Embedded Adaptec AIC-7880 Scsi Controller

Page 106

Configuration Settings Required for Installing MP-RAS

Embedded Adaptec AIC-7880 SCSI Controller

∙On Board SCSI AIC-7880 – Enabled

∙Boot device – Enabled

∙Configure the on board SCSI to IRQ 11

Disk Array Adapter Mylex RAID Controller

∙Disable the on board SCSI boot device in BIOS Setup. This is the “Boot Device” found under “On Board SCSI AIC-7880” in the BIOS Setup.

∙Do not disable the “On Board SCSI AIC-7880” if the intended boot drive is not connected to the RAID controller.

∙Configure IRQ 14 (INTA 14) to RAID controller.

11-16

Installing MP-RAS

Image 106

Contents NCR S16 Minitower Server Page Contents Installing Windows NT Server 4.0 Enterprise Edition Installing SCO Unix ViContents About This Book PrefaceWho Should Read This Book Conventions Used in This Book Related PublicationsInstallation Overview Overview Documentation Needed for Setup Where to Start Step What to Do How to Do It Where to Find InformationConfirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings Return to Page 1, and set parameters as followsECC Power Management Mode Configuring PCI Adapters Inta Intb Intc IntdConfiguring PCI Adapters Configuring PCI Adapters Confirming the Scsi Adapter Settings Confirming the Scsi Adapter Settings Configuring the Scsi Adapters For Wide devices onlyConfiguring the Scsi Adapters Send Start Unit Command Installing Microsoft Windows NT Server Installing Microsoft Windows NT Server Performing a Full Installation of Windows NT Server Entering Windows SetupInstalling from the CD-ROM Inserting the Windows NT Server Setup DiskPreparing the Hard Disk Performing a Full Installation of Windows NT Server Performing a Full Installation of Windows NT Server Completing User and Server Information ContinueSelecting Network Protocols Providing Additional Setup Information Completing the Installation Performing a Full Installation of Windows NT Server Page Installing Microsoft Windows NT Server Overview Starting the Pre-Loaded Installation Pre-Loaded InstallationEntering the Setup Routine for NCR Server Manager Completing the Pre-loaded Installation Pre-Loaded Installation Non-Pre-Load Installation Performing a Full Installation of Windows NT Server Preparing the Hard Disk Performing a Full Installation of Windows NT Server Installing the Network Selecting Network Protocols Entering Additional Setup Information Installing Windows NT Server 4.0 Enterprise Edition Action Reference Install Service Pack Enable 4 GB Support Boot.ini File Before Modification ExampleBoot.ini File After Modification Example Enable 4 GB Support Installing Netware Installing Netware Installation Overview Rebooting the Server and Creating a Primary DOS Partition Rebooting the Server and Creating a Primary DOS Partition Using an Adaptec Controller Loading the Controller’s DriversLoading the CD-ROM as a NetWare Volume Installing NetWare Switching to the System Console Screen Choosing DriversCompleting the Installation Load Smcpwr SLOT=? FRAME=???? NAME=SMCPWR1E83 Installing NetWare Installing SCO Unix Installing SCO Unix Installation Overview Rebooting the Server and Installing the Operating System Entering Setup InformationInserting the Supplement Volume Disk Inserting the CD-ROMRebooting the System SCO Release 3 Installing TCP/IP Communications Inserting the Latest SMC Driver DiskCompleting the Installation SCO Release 5 Installing TCP/IP Communications Inserting the SMC SuperDiskSelect Add Protocol. Observe the following Installing UnixWare Installing UnixWare Installation Overview Inserting the Host Bus Adapter HBA Driver Selecting the Installation Method Observing Screen MessagesReinserting the Host Bus Adapter HBA Driver Disk Entering a Password and Completing the Installation Rebooting the Server and Installing the Operating System Installing OS/2 10-2 Installation Overview 10-4 Editing CONFIG.SYS and Rebooting Installing OS/2 Installing MP-RAS Installing MP-RAS Installation Overview Default Installation Overview Restarting the Installation Performing a Default Installation Booting from the Installation MediaSelecting the Type of Installation Selecting the Install Media Device Entering the System Name, Date, and TimeSpecifying the Secondary Disk Installing Licenses Install Licenses MethodsLicenses, press a 11-12 Turning the System Off Performing Additional Administrative Tasks Configuration Settings Required for Installing MP-RAS Shadow OptionsEmbedded Adaptec AIC-7880 Scsi Controller Used Resources 11-18