NCR S16 manual Performing a Default Installation, Booting from the Installation Media

Page 96

Performing a Default Installation

Performing a Default Installation

The following sections outline the default installation procedure.

Booting from the Installation Media

To install the NCR UNIX SVR4 MP-RAS 3.01.01 operating system software, you must boot the system from Boot flex #1. Follow these steps:

1.Insert Boot flex #1 in the flex disk drive.

2.This step depends on the current operating state of the system.

If the system is powered down, turn on the monitor and the main unit, and go to Step 4.

If the machine is currently up and running, you must perform an orderly shutdown of the operating system. Go to Step 3.

3.Perform an orderly shutdown by logging in as root and entering the following command from the / (root) directory:

# shutdown -y -i6 -gx

(where x=number of seconds to wait until shutdown)

As the system performs its shutdown procedure, a series of messages displays. This may take awhile.

4. During the UNIX system boot process, the following message displays:

Please insert Boot flex #2 and press ENTER >

5.Remove Boot flex #1. Insert Boot flex #2 and press Enter. A series of messages displays.

If a message similar to the following displays, go to Step 6. Otherwise, go to Step 7.

Remote

Console

has been detected. Terminal

type is

set to

vt100.

 

 

Do you

wish to

change it to AT386? (n)/y >

 

6.If you want to change the terminal type, type y and press Enter. If you do not want to change the terminal type, press Enter.

11-6

Installing MP-RAS

Image 96
Contents NCR S16 Minitower Server Page Contents Installing Windows NT Server 4.0 Enterprise Edition Installing SCO Unix ViContents Preface About This BookWho Should Read This Book Conventions Used in This Book Related PublicationsInstallation Overview Overview Documentation Needed for Setup Where to Start Step What to Do How to Do It Where to Find InformationConfirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings Return to Page 1, and set parameters as followsECC Power Management Mode Configuring PCI Adapters Inta Intb Intc IntdConfiguring PCI Adapters Configuring PCI Adapters Confirming the Scsi Adapter Settings Confirming the Scsi Adapter Settings Configuring the Scsi Adapters For Wide devices onlyConfiguring the Scsi Adapters Send Start Unit Command Installing Microsoft Windows NT Server Installing Microsoft Windows NT Server Performing a Full Installation of Windows NT Server Entering Windows SetupInserting the Windows NT Server Setup Disk Installing from the CD-ROMPreparing the Hard Disk Performing a Full Installation of Windows NT Server Performing a Full Installation of Windows NT Server Completing User and Server Information ContinueSelecting Network Protocols Providing Additional Setup Information Completing the Installation Performing a Full Installation of Windows NT Server Page Installing Microsoft Windows NT Server Overview Pre-Loaded Installation Starting the Pre-Loaded InstallationEntering the Setup Routine for NCR Server Manager Completing the Pre-loaded Installation Pre-Loaded Installation Non-Pre-Load Installation Performing a Full Installation of Windows NT Server Preparing the Hard Disk Performing a Full Installation of Windows NT Server Installing the Network Selecting Network Protocols Entering Additional Setup Information Installing Windows NT Server 4.0 Enterprise Edition Action Reference Install Service Pack Enable 4 GB Support Boot.ini File Before Modification ExampleBoot.ini File After Modification Example Enable 4 GB Support Installing Netware Installing Netware Installation Overview Rebooting the Server and Creating a Primary DOS Partition Rebooting the Server and Creating a Primary DOS Partition Using an Adaptec Controller Loading the Controller’s DriversLoading the CD-ROM as a NetWare Volume Installing NetWare Switching to the System Console Screen Choosing DriversCompleting the Installation Load Smcpwr SLOT=? FRAME=???? NAME=SMCPWR1E83 Installing NetWare Installing SCO Unix Installing SCO Unix Installation Overview Rebooting the Server and Installing the Operating System Entering Setup InformationInserting the Supplement Volume Disk Inserting the CD-ROMRebooting the System SCO Release 3 Installing TCP/IP Communications Inserting the Latest SMC Driver DiskCompleting the Installation SCO Release 5 Installing TCP/IP Communications Inserting the SMC SuperDiskSelect Add Protocol. Observe the following Installing UnixWare Installing UnixWare Installation Overview Inserting the Host Bus Adapter HBA Driver Selecting the Installation Method Observing Screen MessagesReinserting the Host Bus Adapter HBA Driver Disk Entering a Password and Completing the Installation Rebooting the Server and Installing the Operating System Installing OS/2 10-2 Installation Overview 10-4 Editing CONFIG.SYS and Rebooting Installing OS/2 Installing MP-RAS Installing MP-RAS Installation Overview Default Installation Overview Restarting the Installation Performing a Default Installation Booting from the Installation MediaSelecting the Type of Installation Selecting the Install Media Device Entering the System Name, Date, and TimeSpecifying the Secondary Disk Installing Licenses Install Licenses MethodsLicenses, press a 11-12 Turning the System Off Performing Additional Administrative Tasks Configuration Settings Required for Installing MP-RAS Shadow OptionsEmbedded Adaptec AIC-7880 Scsi Controller Used Resources 11-18