NCR S16 manual Installing NetWare

Page 62

Installing NetWare

Installing NetWare

During the installation processes, you are asked many hardware-specific questions. Most of these can be answered by choosing the default (highlighted) option, but in some cases specific information is required.

Note: Know your hardware before attempting this installation. You should install all drivers for your network interface boards on the hard drive where they can be accessed easily. For example, for SMC adapters, you should install the files in the directory, c:\smc.

To install NetWare, follow these steps:

1.At the CD-ROM drive letter prompt (D:, for example), type INSTALL.

2.When prompted to “Select the type of installation desired,” select NetWare Server Installation and press Enter.

3.When prompted to “Choose the product you want to install,” select NetWare 4.1 and press Enter.

4.When prompted to “Select the type of installation you are performing,” select Simple Installation of NetWare 4.1 and press Enter.

5.When prompted to “Specify the server name,” enter a short descriptive alphanumeric title and press Enter.

6.Assign an internal IPX number. To select the default, press Enter.

7.Select the source and destination paths. To select the defaults, press Enter.

8.Select a local configuration and press Enter.

9.Select a filename format. Press Enter to select DOS.

10.To specify special startup commands, select Yes and press Enter. Otherwise, select No.

11.To allow NetWare to run from AUTOEXEC.BAT, select Yes and press Enter. Otherwise, select No.

7-8

Installing Netware

Image 62
Contents NCR S16 Minitower Server Page Contents Installing Windows NT Server 4.0 Enterprise Edition Installing SCO Unix ViContents Who Should Read This Book PrefaceAbout This Book Conventions Used in This Book Related PublicationsInstallation Overview Overview Documentation Needed for Setup Where to Start Step What to Do How to Do It Where to Find InformationConfirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings Return to Page 1, and set parameters as followsECC Power Management Mode Configuring PCI Adapters Inta Intb Intc IntdConfiguring PCI Adapters Configuring PCI Adapters Confirming the Scsi Adapter Settings Confirming the Scsi Adapter Settings Configuring the Scsi Adapters For Wide devices onlyConfiguring the Scsi Adapters Send Start Unit Command Installing Microsoft Windows NT Server Installing Microsoft Windows NT Server Performing a Full Installation of Windows NT Server Entering Windows SetupPreparing the Hard Disk Inserting the Windows NT Server Setup DiskInstalling from the CD-ROM Performing a Full Installation of Windows NT Server Performing a Full Installation of Windows NT Server Completing User and Server Information ContinueSelecting Network Protocols Providing Additional Setup Information Completing the Installation Performing a Full Installation of Windows NT Server Page Installing Microsoft Windows NT Server Overview Entering the Setup Routine for NCR Server Manager Pre-Loaded InstallationStarting the Pre-Loaded Installation Completing the Pre-loaded Installation Pre-Loaded Installation Non-Pre-Load Installation Performing a Full Installation of Windows NT Server Preparing the Hard Disk Performing a Full Installation of Windows NT Server Installing the Network Selecting Network Protocols Entering Additional Setup Information Installing Windows NT Server 4.0 Enterprise Edition Action Reference Install Service Pack Enable 4 GB Support Boot.ini File Before Modification ExampleBoot.ini File After Modification Example Enable 4 GB Support Installing Netware Installing Netware Installation Overview Rebooting the Server and Creating a Primary DOS Partition Rebooting the Server and Creating a Primary DOS Partition Using an Adaptec Controller Loading the Controller’s DriversLoading the CD-ROM as a NetWare Volume Installing NetWare Switching to the System Console Screen Choosing DriversCompleting the Installation Load Smcpwr SLOT=? FRAME=???? NAME=SMCPWR1E83 Installing NetWare Installing SCO Unix Installing SCO Unix Installation Overview Rebooting the Server and Installing the Operating System Entering Setup InformationInserting the Supplement Volume Disk Inserting the CD-ROMRebooting the System SCO Release 3 Installing TCP/IP Communications Inserting the Latest SMC Driver DiskCompleting the Installation SCO Release 5 Installing TCP/IP Communications Inserting the SMC SuperDiskSelect Add Protocol. Observe the following Installing UnixWare Installing UnixWare Installation Overview Inserting the Host Bus Adapter HBA Driver Selecting the Installation Method Observing Screen MessagesReinserting the Host Bus Adapter HBA Driver Disk Entering a Password and Completing the Installation Rebooting the Server and Installing the Operating System Installing OS/2 10-2 Installation Overview 10-4 Editing CONFIG.SYS and Rebooting Installing OS/2 Installing MP-RAS Installing MP-RAS Installation Overview Default Installation Overview Restarting the Installation Performing a Default Installation Booting from the Installation MediaSelecting the Type of Installation Selecting the Install Media Device Entering the System Name, Date, and TimeSpecifying the Secondary Disk Installing Licenses Install Licenses MethodsLicenses, press a 11-12 Turning the System Off Performing Additional Administrative Tasks Configuration Settings Required for Installing MP-RAS Shadow OptionsEmbedded Adaptec AIC-7880 Scsi Controller Used Resources 11-18