NCR S16 manual Selecting Network Protocols

Page 47

Performing a Full Installation of Windows NT Server 4.0

3.When prompted to have the setup utility search for your network adapters, choose Select from List and Have Disk.

4.Insert your network interface board driver disk. Select the appropriate driver, and select NEXT.

Selecting Network Protocols

Continue the installation by selecting network protocols. Follow these steps:

1.The Windows NT Server installation procedure prepares your available choices for network protocols. You may select any of the protocol transports listed: NWLink (IPX/SPX), TCP/IP, or NetBEUI. When you have selected the checkboxes of all protocols you want to install, select NEXT.

2.Verify the network services that will be installed to the system. Make any needed changes and select NEXT.

3.To install the selected components, select NEXT.

4.When prompted, setup your network boards, and select CONTINUE.

5.When prompted to configure the parameters for the TCP/IP transport, and you chose to install it, ask your network administrator for information you need to configure this service.

6.You may choose to enable the Dynamic Host Configuration Protocol, if this system is to be connected to a DHCP server. If not, you must enter the appropriate IP Address and Subnet Mask and the Default Gateway, if routing outside of your local subnet.

7.You may also choose to enter the IP addresses of your primary and secondary WINS server. When finished, select OK.

8.Installation of the network components continues. If you indicated earlier that you want this system to be a Domain Controller, you are prompted to choose if this system is to be a Primary Domain Controller or a Backup Domain Controller. In either case, you must complete the domain name.

Note: Do not include spaces or backward slashes in the domain name. When you have finished, select OK.

NCR S16 Minitower Server Installing Network Operating System

5-11

Image 47
Contents NCR S16 Minitower Server Page Contents Installing Windows NT Server 4.0 Enterprise Edition Installing SCO Unix ViContents Who Should Read This Book PrefaceAbout This Book Related Publications Conventions Used in This BookInstallation Overview Overview Documentation Needed for Setup Step What to Do How to Do It Where to Find Information Where to StartConfirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings and Configuring PCI Adapters Return to Page 1, and set parameters as follows Confirming the Cmos SettingsECC Power Management Mode Inta Intb Intc Intd Configuring PCI AdaptersConfiguring PCI Adapters Configuring PCI Adapters Confirming the Scsi Adapter Settings Confirming the Scsi Adapter Settings For Wide devices only Configuring the Scsi AdaptersConfiguring the Scsi Adapters Send Start Unit Command Installing Microsoft Windows NT Server Installing Microsoft Windows NT Server Entering Windows Setup Performing a Full Installation of Windows NT ServerPreparing the Hard Disk Inserting the Windows NT Server Setup DiskInstalling from the CD-ROM Performing a Full Installation of Windows NT Server Performing a Full Installation of Windows NT Server Continue Completing User and Server InformationSelecting Network Protocols Providing Additional Setup Information Completing the Installation Performing a Full Installation of Windows NT Server Page Installing Microsoft Windows NT Server Overview Entering the Setup Routine for NCR Server Manager Pre-Loaded InstallationStarting the Pre-Loaded Installation Completing the Pre-loaded Installation Pre-Loaded Installation Non-Pre-Load Installation Performing a Full Installation of Windows NT Server Preparing the Hard Disk Performing a Full Installation of Windows NT Server Installing the Network Selecting Network Protocols Entering Additional Setup Information Installing Windows NT Server 4.0 Enterprise Edition Action Reference Install Service Pack Boot.ini File Before Modification Example Enable 4 GB SupportBoot.ini File After Modification Example Enable 4 GB Support Installing Netware Installing Netware Installation Overview Rebooting the Server and Creating a Primary DOS Partition Rebooting the Server and Creating a Primary DOS Partition Loading the Controller’s Drivers Using an Adaptec ControllerLoading the CD-ROM as a NetWare Volume Installing NetWare Choosing Drivers Switching to the System Console ScreenCompleting the Installation Load Smcpwr SLOT=? FRAME=???? NAME=SMCPWR1E83 Installing NetWare Installing SCO Unix Installing SCO Unix Installation Overview Entering Setup Information Rebooting the Server and Installing the Operating SystemInserting the CD-ROM Inserting the Supplement Volume DiskRebooting the System Inserting the Latest SMC Driver Disk SCO Release 3 Installing TCP/IP CommunicationsCompleting the Installation Inserting the SMC SuperDisk SCO Release 5 Installing TCP/IP CommunicationsSelect Add Protocol. Observe the following Installing UnixWare Installing UnixWare Installation Overview Inserting the Host Bus Adapter HBA Driver Observing Screen Messages Selecting the Installation MethodReinserting the Host Bus Adapter HBA Driver Disk Entering a Password and Completing the Installation Rebooting the Server and Installing the Operating System Installing OS/2 10-2 Installation Overview 10-4 Editing CONFIG.SYS and Rebooting Installing OS/2 Installing MP-RAS Installing MP-RAS Installation Overview Default Installation Overview Restarting the Installation Booting from the Installation Media Performing a Default InstallationSelecting the Type of Installation Entering the System Name, Date, and Time Selecting the Install Media DeviceSpecifying the Secondary Disk Install Licenses Methods Installing LicensesLicenses, press a 11-12 Turning the System Off Performing Additional Administrative Tasks Shadow Options Configuration Settings Required for Installing MP-RASEmbedded Adaptec AIC-7880 Scsi Controller Used Resources 11-18