NCR S16 manual Installation Overview

Page 57

Installation Overview

Installation Overview

To install NetWare on your server, follow these steps:

∙Confirm CMOS configuration - See Chapter 2

∙Configure adapter settings using the Adaptec BIOS SCSISelect Utility - See Chapter 3

∙Reboot the system and create a primary DOS partition

∙Load the controller’s drivers

∙Install the NetWare software

NCR S16 Minitower Server Installing Network Operating System

7-3

Image 57

Contents NCR S16 Minitower Server Page Contents Installing Windows NT Server 4.0 Enterprise Edition Installing SCO Unix ViContents Preface About This BookWho Should Read This Book Related Publications Conventions Used in This BookInstallation Overview Overview Documentation Needed for Setup Step What to Do How to Do It Where to Find Information Where to StartConfirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings and Configuring PCI Adapters Return to Page 1, and set parameters as follows Confirming the Cmos SettingsECC Power Management Mode Inta Intb Intc Intd Configuring PCI AdaptersConfiguring PCI Adapters Configuring PCI Adapters Confirming the Scsi Adapter Settings Confirming the Scsi Adapter Settings For Wide devices only Configuring the Scsi AdaptersConfiguring the Scsi Adapters Send Start Unit Command Installing Microsoft Windows NT Server Installing Microsoft Windows NT Server Entering Windows Setup Performing a Full Installation of Windows NT ServerInserting the Windows NT Server Setup Disk Installing from the CD-ROMPreparing the Hard Disk Performing a Full Installation of Windows NT Server Performing a Full Installation of Windows NT Server Continue Completing User and Server InformationSelecting Network Protocols Providing Additional Setup Information Completing the Installation Performing a Full Installation of Windows NT Server Page Installing Microsoft Windows NT Server Overview Pre-Loaded Installation Starting the Pre-Loaded InstallationEntering the Setup Routine for NCR Server Manager Completing the Pre-loaded Installation Pre-Loaded Installation Non-Pre-Load Installation Performing a Full Installation of Windows NT Server Preparing the Hard Disk Performing a Full Installation of Windows NT Server Installing the Network Selecting Network Protocols Entering Additional Setup Information Installing Windows NT Server 4.0 Enterprise Edition Action Reference Install Service Pack Boot.ini File Before Modification Example Enable 4 GB SupportBoot.ini File After Modification Example Enable 4 GB Support Installing Netware Installing Netware Installation Overview Rebooting the Server and Creating a Primary DOS Partition Rebooting the Server and Creating a Primary DOS Partition Loading the Controller’s Drivers Using an Adaptec ControllerLoading the CD-ROM as a NetWare Volume Installing NetWare Choosing Drivers Switching to the System Console ScreenCompleting the Installation Load Smcpwr SLOT=? FRAME=???? NAME=SMCPWR1E83 Installing NetWare Installing SCO Unix Installing SCO Unix Installation Overview Entering Setup Information Rebooting the Server and Installing the Operating SystemInserting the CD-ROM Inserting the Supplement Volume DiskRebooting the System Inserting the Latest SMC Driver Disk SCO Release 3 Installing TCP/IP CommunicationsCompleting the Installation Inserting the SMC SuperDisk SCO Release 5 Installing TCP/IP CommunicationsSelect Add Protocol. Observe the following Installing UnixWare Installing UnixWare Installation Overview Inserting the Host Bus Adapter HBA Driver Observing Screen Messages Selecting the Installation MethodReinserting the Host Bus Adapter HBA Driver Disk Entering a Password and Completing the Installation Rebooting the Server and Installing the Operating System Installing OS/2 10-2 Installation Overview 10-4 Editing CONFIG.SYS and Rebooting Installing OS/2 Installing MP-RAS Installing MP-RAS Installation Overview Default Installation Overview Restarting the Installation Booting from the Installation Media Performing a Default InstallationSelecting the Type of Installation Entering the System Name, Date, and Time Selecting the Install Media DeviceSpecifying the Secondary Disk Install Licenses Methods Installing LicensesLicenses, press a 11-12 Turning the System Off Performing Additional Administrative Tasks Shadow Options Configuration Settings Required for Installing MP-RASEmbedded Adaptec AIC-7880 Scsi Controller Used Resources 11-18