NCR S16 manual Overview

Page 38

Overview

Overview

This chapter describes the installation procedure for Microsoft Windows NT Server 4.0 on your server.

The first part of the chapter discusses what you need to do to your system if Microsoft Windows NT Server was pre-loaded at the factory.

WARNING: If MS Windows NT Server was pre-loaded at the factory, heed this warning. Upon first powering on the server, make sure to follow all screen instructions and answer all questions.

Failure to do so or powering off the server before the installation is complete will require you to complete a FULL installation of the operating system.

The second part of the chapter discusses the procedure for installing Microsoft Windows NT Server on your system if it was not pre-loaded at the factory.

5-2	Installing Microsoft Windows NT Server 4.0

Image 38

Contents NCR S16 Minitower Server Page Contents Installing Windows NT Server 4.0 Enterprise Edition Installing SCO Unix ViContents Who Should Read This Book PrefaceAbout This Book Conventions Used in This Book Related PublicationsInstallation Overview Overview Documentation Needed for Setup Where to Start Step What to Do How to Do It Where to Find InformationConfirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings Return to Page 1, and set parameters as followsECC Power Management Mode Configuring PCI Adapters Inta Intb Intc IntdConfiguring PCI Adapters Configuring PCI Adapters Confirming the Scsi Adapter Settings Confirming the Scsi Adapter Settings Configuring the Scsi Adapters For Wide devices onlyConfiguring the Scsi Adapters Send Start Unit Command Installing Microsoft Windows NT Server Installing Microsoft Windows NT Server Performing a Full Installation of Windows NT Server Entering Windows SetupPreparing the Hard Disk Inserting the Windows NT Server Setup DiskInstalling from the CD-ROM Performing a Full Installation of Windows NT Server Performing a Full Installation of Windows NT Server Completing User and Server Information ContinueSelecting Network Protocols Providing Additional Setup Information Completing the Installation Performing a Full Installation of Windows NT Server Page Installing Microsoft Windows NT Server Overview Entering the Setup Routine for NCR Server Manager Pre-Loaded InstallationStarting the Pre-Loaded Installation Completing the Pre-loaded Installation Pre-Loaded Installation Non-Pre-Load Installation Performing a Full Installation of Windows NT Server Preparing the Hard Disk Performing a Full Installation of Windows NT Server Installing the Network Selecting Network Protocols Entering Additional Setup Information Installing Windows NT Server 4.0 Enterprise Edition Action Reference Install Service Pack Enable 4 GB Support Boot.ini File Before Modification ExampleBoot.ini File After Modification Example Enable 4 GB Support Installing Netware Installing Netware Installation Overview Rebooting the Server and Creating a Primary DOS Partition Rebooting the Server and Creating a Primary DOS Partition Using an Adaptec Controller Loading the Controller’s DriversLoading the CD-ROM as a NetWare Volume Installing NetWare Switching to the System Console Screen Choosing DriversCompleting the Installation Load Smcpwr SLOT=? FRAME=???? NAME=SMCPWR1E83 Installing NetWare Installing SCO Unix Installing SCO Unix Installation Overview Rebooting the Server and Installing the Operating System Entering Setup InformationInserting the Supplement Volume Disk Inserting the CD-ROMRebooting the System SCO Release 3 Installing TCP/IP Communications Inserting the Latest SMC Driver DiskCompleting the Installation SCO Release 5 Installing TCP/IP Communications Inserting the SMC SuperDiskSelect Add Protocol. Observe the following Installing UnixWare Installing UnixWare Installation Overview Inserting the Host Bus Adapter HBA Driver Selecting the Installation Method Observing Screen MessagesReinserting the Host Bus Adapter HBA Driver Disk Entering a Password and Completing the Installation Rebooting the Server and Installing the Operating System Installing OS/2 10-2 Installation Overview 10-4 Editing CONFIG.SYS and Rebooting Installing OS/2 Installing MP-RAS Installing MP-RAS Installation Overview Default Installation Overview Restarting the Installation Performing a Default Installation Booting from the Installation MediaSelecting the Type of Installation Selecting the Install Media Device Entering the System Name, Date, and TimeSpecifying the Secondary Disk Installing Licenses Install Licenses MethodsLicenses, press a 11-12 Turning the System Off Performing Additional Administrative Tasks Configuration Settings Required for Installing MP-RAS Shadow OptionsEmbedded Adaptec AIC-7880 Scsi Controller Used Resources 11-18