Pitney Bowes DA950 manual Barcode, Location, Digit On/Off, Bar Width

Page 77

Printer Menus

Using the Main Menu (continued)

4. Barcode

Use this option to print a USPS barcode. The options on this menu are: A. Location, B. 5 Digit On/Off, and C. Bar Width.

A. Location

Use this option to print the barcode above or below the address, or to stop printing the barcode.

•Above Address prints the barcode in the address block above the first line of the address.

•Below Address prints the barcode below the last line of the address.

•Off stops the barcode from printing.

B. 5 Digit On/Off

Use this option to print a 5 digit barcode for a 5 digit ZIP Code.

NOTE: Only a five digit barcode is printed for a 5 digit ZIP Code. A Delivery Point Barcode cannot be gener- ated from a five digit ZIP Code.

C. Bar Width

Use this option to increase the width or decrease the width of the bars generated for the USPS Postnet and Planet barcodes. Select this item to counteract the vari- ance in the barcodes due to material, print quality, inks, etc. Bar width settings run from 6 to 12.

A-11

Image 77

Contents Page FCC Compliance Contents Chapter Using the DA950 with Your Computer Chapter Troubleshooting Your Printer Appendix B DA950 Specifications Chapter Overview Welcome to the DA950 Printer Using This GuideAppendix A-Using the Control Panel Menus TroubleshootingAppendix B-Specifications System RequirementsWorld Wide Web Getting Help Ordering SuppliesPhone Support Before You Contact Pitney BowesImportant Safety Notes Overview Printer Parts and Locations Printer Parts and Locations Feeder Parts and Locations Feeder Parts and Locations Setting Up Your DA950 Printer Choosing a Location SetupAssembling the Printer Install the Feeder Install the Shock Install the Feed Ramp Install the Side GuidesSetup Assembling Connecting the Parallel Cable or USB CablePrinter Parallel CableConnect the Power Cord and Turn on Install the Print Cartridges Install the Bulk Ink Assembly OptionalPrinter Basics Set the Separator Gap Setting Up a JobBasics Tips for Setting the Separators Setting the Proper Feed GapCenter the Feed Ramp under the Material Set the Feed Ramp Length Set the Feed AnglePosition the Side Guides Load Material Adjust the Media Thickness Knob Print a Test Piece Output StackerSet the Print Head Position Adjust the Takeaway Roller Tension Basics Using the DA950 with Your Computer Installing the Printer Driver Using the Printer with Your ComputerSelecting DA950 Printer From Windows Application About Envelope Designer Plus Making DA950 Default Print DriverAccessing the Print Driver General Tab Paper Size Printing PreferencesPaper Tab Orientation Feautures Tab Feed DelayPrinting Preferences Memory Overlay Print QualityLetter 300 dpi Draft 200 dpi Pause on Package Break Advanced TabPause on Tray Break Printer Maintenance Removing Old Print Cartridges Printer MaintenanceReplacing Print Cartridges Installing New Print Cartridges Removing the Old Bulk Ink Cartridges Installing New Bulk Ink Cartridges Prolonging Life Print Cartridges Preventive Maintenance Cleaning Print Quality ProblemsCleaning the Sensor Cleaning Exit Idler Entry Rollers Cleaning the Wipers Transport Belts Floor Assembly Troubleshooting Your Printer Feed Problems Troubleshooting Your PrinterProblems and Solutions Problem Intermittent FeedProblem No Print Problem Multifeed feeds doubles or skewingProblem Address Smudging Problem Grey or Light Print-Black InkProblem Address Printing is not Sharp Problem Addresses Walking Problem Skewed PrintProblem Unwanted Bolding Problem No Communications Printer Does Not Respond Interface Problems Motor Problems Other ProblemsProblem Motor Turning but no Feed Roller Move Ment Problem Out of MemoryProblem Paper Out or Paper Jam Troubleshooting Your Printer AppendixA This Button Does This Using the Control PanelPrinter Menus Enter Using the MenusPrinter Menus Using the Main Menu Main Menu Menu Options Distance to Right Address LayoutDistance from Left/Distance to Right Line Spacing Distance from TopExecutive Print QualityLetter DraftFont Selection Location BarcodeDigit On/Off Bar WidthClear Memory Address RecoveryGet Addresses Clear Counter Job SettingsLoad SaveImage Overlay Conveyor TimeFirst Image Overlay Clear OverlayPurge Print Head Reset Ink CounterUsing the Setup Menu Setup Menu Menu Options Feeder Signal Using the Setup MenuStop On Feed Err Error On/Quick Off Signal Polarity Active On/Active OffLines Per Address Line TerminationHex Dump Mode MSB Language Symbol SetInch / Millimeter Menu LanguagesTransport Speed Postal Bundle Brk Break Enable/Disable BreakBreak Character Postal Bundle Brk BreakBreak Char Count Pause TimePurge at Start Pre-PurgePeriodic Purge Purge IntervalSelectable Gap Feed GapStream Feed ROM RevisionPrint Head Size Head 2 up down Head 3 up down Head 5 up down Head 6 up down Using the Service MenuAdjust Print Head 3 is now correctly aligned Head 2 misaligned horizontally Heads now aligned horizontally Bank a to Sensor/Bank B to Sensor Test Display Test SystemPrinter Menus AppendixB Speciﬁcations Equipment SpecificationsResident Fonts Print Modes/Print ResolutionDownloadable Fonts User-Definable ParametersEnvironmental Limits Printhead/InkJet CartridgesNoise Level Recommended UsageApproved Media Material SpecificationsMedia Sizes Material NotesTable of Envelope Sizes Name Style Dimensions Inch Dimensions Metric Height x WidthAppendixC Glossary Double feeding Embedded printer commandsDraft quality DriversInternal test address message Interface connectorInterface cable Internal fontsPower socket PCL commandsPoint size PortUniversal Serial Bus USB SubdirectoryIndex Index Index Index Index Page