AMCC 9590SE-4ME manual Cx set ondegrade=cacheofffollow, Cx set spinup=nn, Cx set stagger=nn

Page 56

Chapter 2. CLI Syntax Reference

/cx set ondegrade=cacheofffollow

This command is only for 9500S controllers.

This command allows you to set a controller-based write cache policy. If the policy is set to cacheoff and a unit degrades, the firmware will disable the write-cache on the degraded unit, regardless of what the unit-based write cache policy is. If the policy is set to follow and a unit degrades, firmware will follow whatever cache policy has been set for that unit. (For details about the unit-based policy, see “/cx/ux set cache=onoff [quiet]” on page 61.)

/cx set spinup=nn

This command is only for 9000 series controllers.

This command allows you to set a controller-based Disk Spinup Policy that specifies how many drives can spin up at one time. The value must be a positive integer between 1 and the number of disks/ports supported on the controller (4, 8, or 12). The default is 1.

This policy is used to stagger spinups of disks at boot time in order to spread the power consumption on the power supply. For example, given a spinup policy of 2, the controller will spin up two disks at a time, pause, and then spin up another 2 disks. The amount of time to pause can be specified with the Spinup Stagger Time Policy (/cx set stagger).

Not all drives support staggered spinup. If you enable staggered spinup and have drives that do not support it, the setting will be ignored.

/cx set stagger=nn

This command is only for 9000 series controllers.

This command allows you to set a controller-based Disk Spinup Stagger Time Policy that specifies the delay between spin-ups. The value must be a positive integer between 0 to 60 seconds. This policy, in conjunction with Disk Spinup Policy, specifies how the controller should spin up disks at boot time. The default is 6 seconds.

/cx set autocarve=onoff

This command is only for 9000 series controllers.

This command allows you to set the auto-carve policy to on or off. By default, autocarve is off.

When the auto-carve policy is set to on, any unit larger than the carvesize is created or migrated into one or more carvesize volumes and a remaining

50

3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5

Image 56
Contents Command Line Interface 3wareCopyright Table of Contents Page Cx/ux set autoverify=onoff Return Code About this CLI Guide Page Introduction to the 3ware Command Line Interface Features of the CLISupported Operating Systems TerminologyInstalling the 3ware CLI on Mac OS Working with 3ware CLIUsing the command interface interactively Using a single command with outputUsing an input file to execute a script Outputting the CLI to a Text FileUnderstanding RAID Levels and Concepts ConventionsRAID Concepts Available RAID Configurations RAIDRAID 0 Configuration Example RAID 5 Configuration Example Determining What RAID Level to Use Single DiskUsing Drive Capacity Efficiently Common Tasks Mapped to CLI Commands CLI Syntax ReferenceCommon Tasks Mapped to CLI Commands Common Tasks Mapped to CLI Commands Syntax Overview Shell Object Commands Focus ObjectShow Show ver Show rebuild Show alarms reverseShow diag Show verify Show selftestUpdate fw=filenamewithpath force FlushRescan CommitController Object Commands Cx showCx show Cx show attribute attribute Typical output looks likeCx show bios Cx show driverCx show model Cx show firmwareCx show serial Cx show pcbCx show pchip Cx show achipCx show numports Cx show numunitsCx show ctlbus Cx show exportjbodCx show spinup Cx show staggerCx show ondegrade Cx show autocarveCx show carvesize Cx show memoryCx show autorebuild Cx show unitstatusCx show allunitstatus Cx show drivestatusCx show all 3JV3MVTASupported Stripe Sizes Controller Object Commands Cx rescan noscan Supported Model-Unit Types for ignoreECCCx flush Cx update fw=filenamewithpath forceCx commit Cx show alarms reverse Cx show diagCx show rebuild RAID-5 Initializing Cx show verify Cx show selftest Setting Up a Rebuild Schedule Cx add rebuild=dddhhdurationSetting Up a Verify Schedule Cx add verify=dddhhdurationCx add selftest=dddhh Cx del rebuild=slotidCx del selftest=slotid Cx set rebuild=enabledisable1..5Cx del verify=slotid Cx set exportjbod=onoff Cx set verify=enabledisable1..5Cx set selftest=enabledisable task=UDMASMART Cx set ondegrade=cacheofffollow Cx set spinup=nnCx set stagger=nn Cx set autocarve=onoffCx set carvesize=1024..2048 Cx set autorebuild=onoffCx start mediascan Cx stop mediascanUnit Object Commands Cx/ux showCx/ux show attribute attribute Cx/ux show statusCx/ux show rebuildstatus Cx/ux show verifystatusCx/ux show initializestatus Cx/ux show nameCx/ux show qpolicy Cx/ux show storsaveCx/ux show identify Cx/ux show autoverifyCx/ux show volumes Cx/ux show cacheCx/ux show ignoreECC Cx/ux show allCx/ux remove noscan quiet Cx/ux del noscan quietCx/ux start rebuild disk=pp-p...ignoreECC Cx/ux start verifyCx/ux stop verify Cx/ux pause rebuildCx/ux resume rebuild Cx/ux set cache=onoff quiet Cx/ux flushCx/ux set autoverify=onoff Cx/ux set identify=onoff Cx/ux set ignoreECC=onoffCx/ux set name=string Cx/ux set qpolicy=onoffBy default, qpolicy is off Cx/ux set storsave=protectbalanceperform quietExample Valid Migration Paths Supported Stripe Sizes Migration Process 3JV2Q1VA Cx/px show attribute attribute Port Object CommandsCx/px show Cx/px show status Cx/px show modelCx/px show serial Cx/px show firmwareCx/px show ncq Cx/px show lspeedCx/px show capacity Cx/px show smartCx/px show all Cx/px remove noscan quiet Cx/px set identify=onoffBBU Object Commands Cx/bbu showCx/bbu show attribute attribute Cx/bbu show statusCx/bbu show batinst Cx/bbu show lasttestCx/bbu show volt Cx/bbu show tempCx/bbu show bootloader Cx/bbu show serialCx/bbu show fw Cx/bbu show pcbCx/bbu enable Cx/bbu disable quietEnclosure Object Commands Ex showEx show slots Ex show attribute attributeEx show controllers Ex show fans Ex show tempEx show all Ex/slotx showEx/slotx show identify Ex/slotx set identify=onoffEx/fanx show Ex/tempx showHelp Commands Help with specific commandsHelp with attributes Help flush HelpHelp show Help update Help rescanHelp commit Help focusReturn Code