AMCC 9590SE-4ME manual BBU Object Commands, Cx/bbu show

Page 80

Chapter 2. CLI Syntax Reference

BBU Object Commands

BBU (Battery Backup Unit) Object Commands are commands that provide information and perform actions related to a specific BBU installed on a specific controller, such as /c0/bbu.

This object is only available on 9000 series controllers on which a BBU is actually installed. (The BBU is not supported on 9590SE-4ME.)

Syntax

/cx/bbu show

(9000

only)

/cx/bbu show attribute [attribute ...] where attributes are:

batinstbootloadercapfwlasttestpcbreadyserial

statustempvolt

(9000

only)

/cx/bbu show all

/cx/bbu test [quiet]

(9000

only)

Warning: May take up to 24 hours to complete. Write cache

will be disabled during the test.

(9000

only)

/cx/bbu

enable

/cx/bbu

disable [quiet]

(9000

only)

/cx/bbu show

This command presents a summary report on the specified BBU object.

Example:

//localhost> /c0/bbu show

Volt

Temp

Hours LastCapTest

Name OnlineState BBUReady Status

---------------------------------------------------------------------------

bbu ON

No

Testing

OK

OK

72

01-Jul-2004

The command output indicates that the battery capacity was last measured on 01-Jul-2004. The battery is estimated to last for 72 hours from the last tested date. In this example, the BBU unit is currently testing the battery. Both voltage and temperature are normal. The BBU is not ready to backup the write cache on the controller (due to the testing). (For complete information about the BBU, see the user guide that came with your 3ware RAID controller).

Note: If the BBU is either not present or disabled, the following will be displayed after the command //localhost> /c0/bbu show.

Error: (CLI:053) Battery Backup Unit is not present.

74

3ware Serial ATA RAID Controller CLI Guide for the Power Mac G5

Image 80
Contents Command Line Interface 3wareCopyright Table of Contents Page Cx/ux set autoverify=onoff Return Code About this CLI Guide Page Introduction to the 3ware Command Line Interface Features of the CLISupported Operating Systems TerminologyInstalling the 3ware CLI on Mac OS Working with 3ware CLIUsing the command interface interactively Using a single command with outputUsing an input file to execute a script Outputting the CLI to a Text FileUnderstanding RAID Levels and Concepts ConventionsRAID Concepts Available RAID Configurations RAIDRAID 0 Configuration Example RAID 5 Configuration Example Determining What RAID Level to Use Single DiskUsing Drive Capacity Efficiently Common Tasks Mapped to CLI Commands CLI Syntax ReferenceCommon Tasks Mapped to CLI Commands Common Tasks Mapped to CLI Commands Syntax Overview Shell Object Commands Focus ObjectShow Show ver Show rebuild Show alarms reverseShow diag Show verify Show selftestUpdate fw=filenamewithpath force FlushRescan CommitController Object Commands Cx showCx show Cx show attribute attribute Typical output looks likeCx show bios Cx show driverCx show model Cx show firmwareCx show serial Cx show pcbCx show pchip Cx show achipCx show numports Cx show numunitsCx show ctlbus Cx show exportjbodCx show spinup Cx show staggerCx show ondegrade Cx show autocarveCx show carvesize Cx show memoryCx show autorebuild Cx show unitstatusCx show allunitstatus Cx show drivestatusCx show all 3JV3MVTASupported Stripe Sizes Controller Object Commands Cx rescan noscan Supported Model-Unit Types for ignoreECCCx flush Cx update fw=filenamewithpath forceCx commit Cx show alarms reverse Cx show diagCx show rebuild RAID-5 Initializing Cx show verify Cx show selftest Setting Up a Rebuild Schedule Cx add rebuild=dddhhdurationSetting Up a Verify Schedule Cx add verify=dddhhdurationCx add selftest=dddhh Cx del rebuild=slotidCx del selftest=slotid Cx set rebuild=enabledisable1..5Cx del verify=slotid Cx set exportjbod=onoff Cx set verify=enabledisable1..5Cx set selftest=enabledisable task=UDMASMART Cx set ondegrade=cacheofffollow Cx set spinup=nnCx set stagger=nn Cx set autocarve=onoffCx set carvesize=1024..2048 Cx set autorebuild=onoffCx start mediascan Cx stop mediascanUnit Object Commands Cx/ux showCx/ux show attribute attribute Cx/ux show statusCx/ux show rebuildstatus Cx/ux show verifystatusCx/ux show initializestatus Cx/ux show nameCx/ux show qpolicy Cx/ux show storsaveCx/ux show identify Cx/ux show autoverifyCx/ux show volumes Cx/ux show cacheCx/ux show ignoreECC Cx/ux show allCx/ux remove noscan quiet Cx/ux del noscan quietCx/ux start rebuild disk=pp-p...ignoreECC Cx/ux start verifyCx/ux stop verify Cx/ux pause rebuildCx/ux resume rebuild Cx/ux set cache=onoff quiet Cx/ux flushCx/ux set autoverify=onoff Cx/ux set identify=onoff Cx/ux set ignoreECC=onoffCx/ux set name=string Cx/ux set qpolicy=onoffBy default, qpolicy is off Cx/ux set storsave=protectbalanceperform quietExample Valid Migration Paths Supported Stripe Sizes Migration Process 3JV2Q1VA Cx/px show attribute attribute Port Object CommandsCx/px show Cx/px show status Cx/px show modelCx/px show serial Cx/px show firmwareCx/px show ncq Cx/px show lspeedCx/px show capacity Cx/px show smartCx/px show all Cx/px remove noscan quiet Cx/px set identify=onoffBBU Object Commands Cx/bbu showCx/bbu show attribute attribute Cx/bbu show statusCx/bbu show batinst Cx/bbu show lasttestCx/bbu show volt Cx/bbu show tempCx/bbu show bootloader Cx/bbu show serialCx/bbu show fw Cx/bbu show pcbCx/bbu enable Cx/bbu disable quietEnclosure Object Commands Ex showEx show slots Ex show attribute attributeEx show controllers Ex show fans Ex show tempEx show all Ex/slotx showEx/slotx show identify Ex/slotx set identify=onoffEx/fanx show Ex/tempx showHelp Commands Help with specific commandsHelp with attributes Help flush HelpHelp show Help update Help rescanHelp commit Help focusReturn Code