Graco 24B596, 24B591 System Wiring Options Alarm Out, 30VDC, 100/240VAC

Page 16

Installation

System Wiring Options: Alarm Out

9 - 30VDC

-PWR+

OUTPUTS

J7

1(IN)

2(COM)

3(OUT1)

4(COM)

5(OUT2)

6(COM)

7(OUT3)

8(COM)

9(OUT4)

10(OUT4)

11 NC

Low Level

Alarm

				1 A Fuse		+
				1 A Fuse
							Alarm +9-30V
							1 Amp Max

1 A Fuse				+
1 A Fuse					Alarm +9-30V
					Alarm +9-30V
					1 Amp Max

J6


	16		(SW-)
	16		(SW-)		Count
	15		(SEN4)		Count
	15		(SEN4)
	14		(IN4)
	13		(SW+)
	13		(SW+)
	12
	12		(SW-)		Manual
	11 (SEN3)				Manual
	11 (SEN3)
	10		(IN3)
	9	(SW+)

	8	(SW-)
	7	(SEN2)			Low Level
	6	(IN2)
	5	(SW+)
	5	(SW+)
	4	(SW-)
	4	(SW-)
	3	(SEN1)			Press/ Cycle
	3	(SEN1)
	2	(IN1)
	1	(SW+)

Aux (cycle, pressure, machine count)

FIG. 18

100/240VAC

J7

+			1(IN)
-PWR		2(COM)

	3(OUT1)
		4(COM)
	5(OUT2)
OUTPUTS		6(COM)
		6(COM)
	7(OUT3)
		8(COM)
		8(COM)
	9(OUT4)
	10(OUT4)

	11 NC

FIG. 19

Low

Level

			1 A Fuse
Alarm					Alarm 100-240 VAC
					1 Amp Max

1 A Fuse

Alarm 100-240 VAC

1 Amp Max

Aux (cycle, pressure, machine count)

J6


	16		(SW-)
	16		(SW-)		Count
	15		(SEN4)		Count
	15		(SEN4)
	14		(IN4)
	13		(SW+)
	13		(SW+)
	12
	12		(SW-)		Manual
	11 (SEN3)				Manual
	10		(IN3)
	9	(SW+)

	8	(SW-)
	7	(SEN2)			Low Level
	7	(SEN2)
	6	(IN2)
	5	(SW+)
	5	(SW+)
	4	(SW-)

					Press/ Cycle
	3	(SEN1)			Press/ Cycle
	3	(SEN1)
	2	(IN1)
	1	(SW+)

16

313855H

Image 16

Contents Important Safety Instructions GLC Lubrication ControllerElectric Shock Hazard Run Mode Functions Component IdentificationKeypad, Display, and Icons Direction ArrowsIcons Installation Typical InstallationInstalling the Lubrication Controller GroundingSystem Configuration and Wiring System Configurations Modes of OperationSensor Wiring Configurations Optional I/O Wiring DiagramsSystem Configuration Divider Valve SystemDual Line System Injector System Input Sensor Wiring System WiringSource Switch 2 or 3 Wire Type Pump on = Time Pump OFF = Time 30VDCDry Contact, shown. For other configuration, see or FIG Pump on = Cycle or Pressure Pump OFF = TimePump on = Cycle or Pressure Pump OFF = Machine Count System Wiring Options 30VDC System Wiring Options Alarm Out100/240VAC System Setup PIN Mode Enabled SetupSee Electric Connection Warning, System Setup Pump on SetupTimer Setup Main ScreenPressure Setup Cycle END SetupCycle Mode Selection Pump OFF SetupTo Set the Pump OFF Option If Count is selected If Time is selectedIf Both is selected Power UP Setup Power Up can be programmed one of four waysThird At Power Up, immediately go to Pump on normal on time Pulsed Setup Pulsed Pump ScreenPIN Setup To enable PIN Code EntryQuick Cycle Setup Display SetupDisplay Backlight LOW Level Filtering Setup Quick Cycle Screen SetupLow Level Filtering Screen Setup Run Mode Screen IdentificationPump On Ended with Pressure Prelube Power UpPump On Ended with Time Pump Off Ended with Time Pump On Ended with Cycle Switch ActivationPump Off Ended with Machine Counts Alarms Screen Pump Off Ended with Machine Counts Max Time EnteredTroubleshooting Program SettingsDescription Problem Solution Modes of OperationTechnical Data IP69KDimensions Mounting Hole LayoutGraco Standard Warranty Graco Information