Graco 24B591, 24B596 If Time is selected, If Count is selected, If Both is selected

Page 21

If TIME is selected:

If TIME is selected you will also be prompted to set the specific amount of time.

FIG. 30

1.Use the Arrow keys to move the cursor over the TIME field.

2.Press ENTER.

NOTE: Time is displayed in HH:MM:SS.

3.Use the UP/DOWN arrows to move up and down through the numbers 0-9 until the first number in the pump off TIME is displayed in the field.

4.Use the RIGHT arrow to move the cursor to the next field.

5.Repeat steps 3 and 4 until the desired time is dis- played.

6.Press RESET. The Main Screen, page 18 displays.

If COUNT is selected:

If COUNT is selected you will also be prompted to set the specific number of counts.

FIG. 31

Setup

1.Use the Arrow keys to move the cursor over the COUNTS field.

2.Press ENTER.

3.Use the UP/DOWN arrows to move up and down through the numbers 0-9 until the first number you want in the COUNTS field is displayed.

4.Use the RIGHT arrow to move the cursor to the next field. Repeat step 3.

NOTE: The maximum number of Counts you can setup in this field is 9999.

5. Press RESET. The Main Screen, page 18 displays.

If BOTH is selected:

If PUMP OFF is set to BOTH, the GLC 4400 will stay in the PUMP OFF state until the entered number of machine counts is received or the time expires.

If TIMEOUT is set to FAULT, an alarm will occur when the time expires.

If TIMEOUT is set to RUN, the unit will enter PUMP ON when time expires.

If BOTH is selected you will be prompted to set the spe- cific amount of time and determine what occurs when time expires.

FIG. 32

1.Use the Arrow keys to move the cursor over the COUNTS field.

2.Press ENTER.

3.Use the UP/DOWN arrows to move up and down through the numbers 0-9 until the first number you want in the COUNTS field is displayed.

313855H

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents GLC Lubrication Controller Important Safety InstructionsElectric Shock Hazard Component Identification Run Mode FunctionsKeypad, Display, and Icons Direction ArrowsIcons Typical Installation InstallationGrounding Installing the Lubrication ControllerSystem Configurations Modes of Operation System Configuration and WiringSensor Wiring Configurations Optional I/O Wiring DiagramsDivider Valve System System ConfigurationDual Line System Injector System System Wiring Input Sensor WiringSource Switch 2 or 3 Wire Type 30VDC Pump on = Time Pump OFF = TimePump on = Cycle or Pressure Pump OFF = Time Dry Contact, shown. For other configuration, see or FIGPump on = Cycle or Pressure Pump OFF = Machine Count System Wiring Options System Wiring Options Alarm Out 30VDC100/240VAC Setup System Setup PIN Mode EnabledSee Electric Connection Warning, Pump on Setup System Setup Timer Setup Main ScreenCycle END Setup Pressure SetupPump OFF Setup Cycle Mode SelectionTo Set the Pump OFF Option If Time is selected If Count is selectedIf Both is selected Power Up can be programmed one of four ways Power UP SetupThird At Power Up, immediately go to Pump on normal on time Pulsed Pump Screen Pulsed SetupTo enable PIN Code Entry PIN SetupDisplay Setup Quick Cycle SetupDisplay Backlight Quick Cycle Screen Setup LOW Level Filtering SetupLow Level Filtering Screen Setup Screen Identification Run ModePrelube Power Up Pump On Ended with PressurePump On Ended with Time Pump On Ended with Cycle Switch Activation Pump Off Ended with TimePump Off Ended with Machine Counts Pump Off Ended with Machine Counts Max Time Entered Alarms ScreenProgram Settings TroubleshootingDescription Problem Solution Modes of OperationIP69K Technical DataMounting Hole Layout DimensionsGraco Information Graco Standard Warranty
Top Page Image Contents