Panasonic WJ-GXE500E manual Action at an alarm occurrence, Save images on the SD memory card

Page 13

Action at an alarm occurrence

The alarm action (action at an alarm occurrence) will be performed when the following alarms occur.

Alarm type

Terminal alarm: When connecting an alarm device such as a sensor to the EXT I/O terminals of the unit, the alarm action will be performed when the connected alarm device is activated. (☞ Page 45)

VMD alarm: When motion is detected in the set VMD area, the alarm action will be performed. (☞ Page 45) * VMD stands for "Video Motion Detection".

Command alarm: When a Panasonic alarm protocol is received from the connected device via a network, the alarm action will be performed. (☞ Page 45)

Camera site alarm: When a camera connected to a Video input connector detects an alarm by alarm sensors or cameras' motion detectors, etc., and the unit receives the alarm input signal from the camera, the alarm action will be performed. (☞ Page 45)

Video loss: When the loss of video input signals is detected due to coaxial cable disconnections or camera trou- bles, the alarm action will be performed. (☞ Page 45)

Action at an alarm occurrence

•Display the [Alarm occurrence indication] button on the "Live" page. (☞ Page 7)

The alarm occurrence indication button will be displayed on the "Live" page at an alarm occurrence.

Important:

•When "Polling (30 sec)" is selected for "Alarm status update mode" (☞ page 30), the [Alarm occurrence indica- tion] button will be refreshed in 30-second intervals. For this reason, it may take a maximum of 30 seconds until the [Alarm occurrence indication] button is displayed on the "Live" page at an alarm occurrence.

•Notify of alarm occurrences to the device connected to the alarm connector

It is possible to output signals from the alarm connector on the rear of the unit and sound the buzzer when an alarm occurs.

The settings for the alarm output can be configured on the [Alarm] tab of the "Alarm" page. (☞ Page 45)

•Save images on the SD memory card

When an alarm occurs, images will be saved on the SD memory card. The settings to save images on the SD memory card can be configured on the [SD memory card] tab of the "Basic" page. (☞ Page 31)

•Transmit an image onto a server automatically

An alarm image can be transmitted at an alarm occurrence to the server designated in advance. The settings required to transmit an alarm image to a server can be configured on the [Alarm] tab of the "Alarm" page and the [FTP] tab of the "Server" page (☞ pages 45 and 52).

Important:

•Select "FTP error" for "Save trigger" on the [SD memory card] tab when using the SD memory card. When

"Alarm input" or "Manual" is selected for "Save trigger", an alarm image will not be transmitted at an alarm occurrence to the FTP server. (☞ Page 31)

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Network Video Encoder Operating InstructionsContents Trademarks and registered trademarks PrefaceAbbreviations About the network security Viewer softwareMonitor images on a PC Example of IPv6 accessMonitor images from a single camera StepWhen Ch1-3 is selected for Ch selection When Ch1-2 is selected for Ch selectionWhen Ch1-4 is selected for Ch selection About the Live AUX buttons *2 2Auto mode *2Rec. on SD button *2 Log button *14Brightness buttons *2 5Preset *26Unit title 7Camera title@4Main area @3SD recording status indicatorMonitor images from multiple cameras Record images on the SD memory card manually Save images on the SD memory card Action at an alarm occurrenceTransmit an image onto a server automatically Notify of alarm occurrences by e-mail Transmit images onto an FTP server Page Number of the listed logs Display the log listTop button Prev. page buttonLast button Next page buttonTime & date EventCh No Number of imagesREW button REV Play buttonPREV. Image button FF buttonPause button Stop buttonError description Maintenance of the unit MaintenanceCheck the system log System log NextUpgrade the firmware Upgrade Load the default Html files setup menu Reset the settings/Reboot the unit Default resetReset to the default and load the default Html files Camera restartDisplaying the Help screen Viewing HelpHow to display the setup menu Display the setup menu from a PCHow to operate the setup menu Setup button About the setup menu window5Setup 4Status display areaMenu Tab Outline Reference Setup menu and its itemsFTP Basic Setup items Setting values Underlined defaultBasic tab QVGA/VGA SD memory card tabPage Log tab JPEG/H.264 tab Image/AudioSetup items Setting values Underlined default Setup items Setting values Underlined default MPEG-4 JPEG/MPEG-4 tabSetup items Setting values Underlined default Setup items Setting values Underlined default Image/Position tab Setup itemsAbout the operation panel Audio tabCoaxial/RS-485 tab Page Multi-screen Multi-screen setup tabAlarm tab AlarmVMD area tab Click the Set button → The edited settings will be applied Notification tab XML notification tab Advanced func.Face detection tab User auth. tab User mng.Host auth. tab System tab Mail tab ServerFTP tab NTP tab Network tab NetworkWAN Ddns tabFTP img. trans. tab Snmp tabSchedule tab ScheduleCategory Indication Description About the displayed system logError indications relating to Ddns Symptom Cause/solution TroubleshootingSymptom Symptom Installation Guide Symptom Cause/solution Reference Pages Information Bar Cause/solution Image capture size VGA AppendixImage capture size Qvga SD memory card is enough, the older images will be SD memory Save trigger Overwrite Save logs Card Log tab SD memory card tab Logs and associated imagesFTP error Images FTP Directory structure of drive BPanasonic Canada Inc
Top Page Image Contents