Panasonic PT-D5700EL, PT-DW5100EL manual Using the remote control unit, Loading dry cells

Page 14

Using the remote control unit

Loading dry cells

When loading batteries into the battery compartment of the remote control, make sure that their polarities are correct.

1. Open battery compartment lid.

Open the lid in the order of steps and .

2. Insert the dry cells.

Into battery compartment, with their polarities orientated as indicated ( , ) in the compartment.

Accessory type-AA dry batteries (insert the negative side first).

3. Close the battery compartment lid.

Replace the battery compartment lid over the compartment and slide until it clicks.

Attention • Do not drop the remote control unit.

Do not expose remote control unit to any liquid.

Do not use NiCd batteries.

Effective range of remote control operation

The remote control should normally be aimed at either the front or rear remote control receiver window on the projector (figure 1). Otherwise, it may also be aimed at the screen, which will reflect commands back to the projector’s front receiver window as illustrated in figure 2.

The effective control range is approx. 30 m from the beam receiver on the front or rear.

Remote

30˚

30˚

Remote

control

 

 

control

30˚ 30˚

(Front)

(Rear)

 

 

[Top view]

 

Remote 15˚

 

 

control

15˚

Remote

15˚

 

control

 

 

[Side view]

15˚

 

Figure 1

Screen

Projector

Remote control

Remote control

receiver window

receiver window

(front)

(rear)

 

Remote control

Figure 2

Note • When the remote control is aimed at the screen, the effective control range may be reduced due to the optical loss by screen reflection.

The remote control may not function properly if an object is in the light path.

The remote control receiver may not function properly in intense ambient light such as fluorescent lamps.

Carefully site the projector so its remote control receiver windows will not be directly exposed to intense light.

14

Image 14
Contents Operating Instructions Dear Panasonic Customer Model number PT-D5700E/PT-D5700EL/PT-DW5100E/PT-DW5100ELFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Do not disassemble the lamp unit Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Always disconnect all cables before moving the projectorDo not place the projector in extremely hot locations AccessoriesDo not use the old lamp unit Precautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Setting projector ID number to remote control Connect to the projector to use with a cableProjection schemes InstallationInstallation geometry Unit mmScreen aspect ratio Projection distance by projection lensPT-D5700E, PT-D5700EL Installation PT-DW5100E, PT-DW5100ELCalculation formulas for projection distance by lens types Setup precautions ConnectionExample of connecting with AV products Example of connecting with PCsPress the I button. on the main unit or the remote control Powering up the projectorMaking adjustment and selection ProjectionPowering off the projector Direct power off functionHow to remove the projection lens How to adjust the lensHow to adjust the FOCUS, Zoom and Shift Status function Automatic adjustmentPress the Status button on the remote control Press the Shutter button againOn-screen menus Structure of menu screensBasic menu operations Menu items settingResetting to the factory default Returning to the previousAdjusting the picture Adjusting the position Keystone Clock PhaseZoom Digital Cinema RealityEdge Blending Input ResolutionClamp Position Press to select an item, and press to adjust the setting XGA ModeSxga Mode Raster PositionColor Matching OPTION1 settingsPress the Enter button Press to adjust the values Press to select R, G, B and WhColor Correction Contrast ModeAuto Signal Back ColorFUNC1 DVI Signal LevelDVI Edid OSD PositionProjector ID OPTION2 settingsInstallation AltitudeLamp Relay Lamp PowerLamp Select RS-232CSystem Information Auto Power OFFPassword Cycle of displayed internal test patternsSystem requirements Setting the networkConnecting the PC Connection examplePassword change Using Web Browser ControlAccessing from the Web browser Click OKBasic control Detail control Monitor informationError information Optics ModuleMail set up Authentication server set up DNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusPJLink security authentication Using the PJLink protocolSupported commands Command Control Description RemarksDisplay Setting Setting the securityPassword Change Control Device SetupCommunication conditions Factory setting Using the serial terminalsPin assignments and signal names Examples of connectionConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications Pin assignments and controlIndication of lamp monitor Clean the air filter Cleaning and replacement of air filterProcedure of cleaning Dismantle the air filterLamp When to replace the Lamp unitReplacing the lamp unit AfterLamp unit will be hot after it has been used Lamp unit replacement stepsRemove the two screws securing the fan unit Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedureNo image Power doesNot turn on Image is blurredSpecifications PT-D5700E PT-D5700EL PT-DW5100ERemote control Power source Length of power cord CabinetOutside dimensions Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMDimensions Installation dimensions diagramFor business users in the European Union Trademark Acknowledgement