Panasonic PT-D5700EL manual Projection, Powering up the projector, Making adjustment and selection

Page 22

Projection

 

 

 

R/PR G/Y B/PB

SYNC/HD VD

 

VIDEO IN S-VIDEO IN

RGB 1 IN

 

 

REMOTE 1

REMOTE 2 IN

IN

SE

IN OUT

 

 

 

Powering up the projector

When using an optional lens, install a projection lens before powering up the projector. (Refer to page 24.)

Remove the lens cover beforehand.

Connect the supplied power cord. (220 - 240 V AC, 50 Hz/60 Hz)

Press the “ I ” marked side of the MAIN POWER switch to turn on the power.

The power indicator lights up red, and the projector is placed in the standby mode.

Press the “ I ” button. [on the main unit or the remote control]

The power indicator illuminates in green and soon the image is projected on the screen.

Making adjustment and selection

It is recommended that the projector be allowed to warm up for at least 30 minutes before any adjustments are made to the focus.

<Using the remote control>

Press the FOCUS button to roughly adjust the focus of the lens.*

Set the projection scheme in “INSTALLATION” setting. (page 36)

Select the input signal by pressing the input selector button to toggle through RGB1, RGB2, VIDEO, S-VIDEO and DVI-D.

Turn the feet, and adjust the tilt of the main unit in the front and rear or left and right.

Note • If the projector is powered up at about 0 ˚C, a warm-up period of approximately five

minutes may be necessary to start projection.

The temperature monitor (TEMP) lights during the warm-up period.

When the warm-up is completed, the temperature monitor (TEMP) turns off and the image is projected on the screen.

If the surrounding temperature is very low and the warm-up period exceeds five minutes, the control determines it as an abnormal condition and turns off the power automatically. If this happens, raise the surrounding temperature to 0 °C or higher and then turn the main power “on” and turn the power “on” ( ).

Use the lens left/right adjustment dial to adjust the direction of the lens. (page 25)

Press the SHIFT button to adjust the “SHIFT”.*

Press the AUTO SETUP button if the input signal is RGB/DVI signal. (page 25)

Press the ZOOM button to fit the image size to the screen size.*

Press the FOCUS button again to adjust the “FOCUS”.*

Press the ZOOM button again to adjust

the “ZOOM” and fit the image size to the screen size.*

*When operating at the projector, please refer to page 24.

22

Image 22
Contents Operating Instructions Dear Panasonic Customer Model number PT-D5700E/PT-D5700EL/PT-DW5100E/PT-DW5100ELFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Do not disassemble the lamp unit Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Always disconnect all cables before moving the projectorDo not use the old lamp unit AccessoriesDo not place the projector in extremely hot locations Precautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Effective range of remote control operation Using the remote control unitLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableProjection schemes InstallationInstallation geometry Unit mmPT-D5700E, PT-D5700EL Projection distance by projection lensScreen aspect ratio Installation PT-DW5100E, PT-DW5100ELCalculation formulas for projection distance by lens types Setup precautions ConnectionExample of connecting with AV products Example of connecting with PCsPress the I button. on the main unit or the remote control Powering up the projectorMaking adjustment and selection ProjectionPowering off the projector Direct power off functionHow to adjust the FOCUS, Zoom and Shift How to adjust the lensHow to remove the projection lens Status function Automatic adjustmentPress the Status button on the remote control Press the Shutter button againOn-screen menus Structure of menu screensBasic menu operations Menu items settingResetting to the factory default Returning to the previousAdjusting the picture Adjusting the position Keystone Clock PhaseZoom Digital Cinema RealityClamp Position Input ResolutionEdge Blending Press to select an item, and press to adjust the setting XGA ModeSxga Mode Raster PositionColor Matching OPTION1 settingsPress the Enter button Press to adjust the values Press to select R, G, B and WhColor Correction Contrast ModeAuto Signal Back ColorFUNC1 DVI Signal LevelDVI Edid OSD PositionProjector ID OPTION2 settingsInstallation AltitudeLamp Relay Lamp PowerLamp Select RS-232CSystem Information Auto Power OFFPassword Cycle of displayed internal test patternsSystem requirements Setting the networkConnecting the PC Connection examplePassword change Using Web Browser ControlAccessing from the Web browser Click OKBasic control Detail control Monitor informationError information Optics ModuleMail set up Authentication server set up DNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusPJLink security authentication Using the PJLink protocolSupported commands Command Control Description RemarksDisplay Setting Setting the securityPassword Change Control Device SetupCommunication conditions Factory setting Using the serial terminalsPin assignments and signal names Examples of connectionConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications Pin assignments and controlIndication of lamp monitor Clean the air filter Cleaning and replacement of air filterProcedure of cleaning Dismantle the air filterLamp When to replace the Lamp unitReplacing the lamp unit AfterLamp unit will be hot after it has been used Lamp unit replacement stepsRemove the two screws securing the fan unit Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedureNo image Power doesNot turn on Image is blurredSpecifications PT-D5700E PT-D5700EL PT-DW5100ERemote control Power source Length of power cord CabinetOutside dimensions Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMDimensions Installation dimensions diagramFor business users in the European Union Trademark Acknowledgement