Panasonic PT-D5700EL, PT-DW5100E Zoom, Clock Phase, Keystone, Digital Cinema Reality, Blanking

Page 30

Adjusting the position

Note • If the picture size is compressed or enlarged by using the 16:9 aspect ratio

when the projector is used for profitable purpose or in the presence of an audience (for example, in a coffee shop or at a hotel etc.), it may infringe the rights of the copyright owner of the original picture.

If a picture with the standard (4:3) aspect ratio is projected at a wide aspect ratio, parts of the picture may run over the screen bounds or the overall picture may be distorted. To view the picture at its original aspect ratio, choose the standard 4:3 aspect ratio.

ZOOM

This enables the enlargement ratio to be changed and the resulting enlarged image displayed.

: The enlargement ratio in the horizontal direction is changed.

: The enlargement ratio in the vertical direction is changed.

CLOCK PHASE

(For RGB/YPBPR signals only)

Clock phase adjustment allows the user to minimize

visible noise with the or button.

Note • When projecting signals whose dot clock frequency is 150 MHz or higher, the noise may not disappear even when the clock phase is adjusted.

Clock phase adjustment is not available for digital signals.

KEYSTONE

KEYSTONE : Keystone distortion can be corrected only along either horizontal bound of the picture.

button: button:

Note • Keystone distortion can be corrected to ±30 ° of the angle of tilt for the projector. However, the greater the correction amount, the more the picture quality will deteriorate, and the harder it will become to achieve a good level of focus. To obtain the best picture quality, set up the projector and screen in such a way that the amount of keystone correction required is as minimal as possible.

The picture size will also change when correction of keystone distortion is carried out.

LINEARITY : After you are finished with keystone adjustment, adjust vertical linearity

with the or button.

Linearity is not adjustable if no correction was made to keystone distortion.

How to use ADVANCED MENU

 

ADVANCED MENU

 

 

 

 

 

 

 

DIGITAL CINEMA REALITY

AUTO

 

 

BLANKING

 

 

 

INPUT RESOLUTION

 

 

 

CLAMP POSITION

1

 

 

EDGE BLENDING

OFF

 

 

RASTER POSITION

 

 

 

XGA MODE

XGA

 

 

SXGA MODE

SXGA

 

MENU SELECT

CHANGE

DIGITAL CINEMA REALITY

Increase the vertical resolution when the S-Video/ Video signal input or 480i, 576i, 1080/60i or 1080/50i signal input is applied.

AUTO : Performs automatic detection and

 

cinema processing. (factory default)

OFF

: Unforced cinema processing

25p FIXED:

 

Forced cinema processing (2:2 pulldown)

 

is performed when a PAL and SECAM,

 

or 576i or 1080/50i signal is input.

30p FIXED:

 

Forced cinema processing (2:2

 

pulldown) is performed when a NTSC,

 

480i or 1080/60i signal is input.

Note

• In “DIGITAL CINEMA REALITY”, the image

quality will be deteriorated if “30p FIXED” or “25p FIXED” is selected when the signal is not a 2:2 pulldown signal. (The vertical resolution will be deteriorated.)

BLANKING

You can perform fine adjustments for blanking if noise appears at the ends of the screen or the image protrudes out of the screen during image projection using a video deck and so on.

: Select the UPPER, LOWER, LEFT or RIGHT adjustment.

: Adjust the blanking width.

For upper adjustment For lower adjustment

For left adjustment

For right adjustment

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

Image 30
Contents Operating Instructions Dear Panasonic Customer Model number PT-D5700E/PT-D5700EL/PT-DW5100E/PT-DW5100ELFor Your SAFETY, Please Read the Following Text Carefully Important the Moulded Plug U.K. onlyContents Precautions with regard to safety Do not disassemble the lamp unit Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Always disconnect all cables before moving the projectorAccessories Do not use the old lamp unitDo not place the projector in extremely hot locations Precautions on handling Remote control Name and function of partsBottom Front and side of the projector Status LED lightsRear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Setting projector ID number to remote control Connect to the projector to use with a cableProjection schemes InstallationInstallation geometry Unit mmProjection distance by projection lens PT-D5700E, PT-D5700ELScreen aspect ratio Installation PT-DW5100E, PT-DW5100ELCalculation formulas for projection distance by lens types Setup precautions ConnectionExample of connecting with AV products Example of connecting with PCsPress the I button. on the main unit or the remote control Powering up the projectorMaking adjustment and selection ProjectionPowering off the projector Direct power off functionHow to adjust the lens How to adjust the FOCUS, Zoom and ShiftHow to remove the projection lens Status function Automatic adjustmentPress the Status button on the remote control Press the Shutter button againOn-screen menus Structure of menu screensBasic menu operations Menu items settingResetting to the factory default Returning to the previousAdjusting the picture Adjusting the position Keystone Clock PhaseZoom Digital Cinema RealityInput Resolution Clamp PositionEdge Blending Press to select an item, and press to adjust the setting XGA ModeSxga Mode Raster PositionColor Matching OPTION1 settingsPress the Enter button Press to adjust the values Press to select R, G, B and WhColor Correction Contrast ModeAuto Signal Back ColorFUNC1 DVI Signal LevelDVI Edid OSD PositionProjector ID OPTION2 settingsInstallation AltitudeLamp Relay Lamp PowerLamp Select RS-232CSystem Information Auto Power OFFPassword Cycle of displayed internal test patternsSystem requirements Setting the networkConnecting the PC Connection examplePassword change Using Web Browser ControlAccessing from the Web browser Click OKBasic control Detail control Monitor informationError information Optics ModuleMail set up Authentication server set up DNS server set up Ping testContents of mail sent Adjust clockNetwork config Network statusPJLink security authentication Using the PJLink protocolSupported commands Command Control Description RemarksDisplay Setting Setting the securityPassword Change Control Device SetupCommunication conditions Factory setting Using the serial terminalsPin assignments and signal names Examples of connectionConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications Pin assignments and controlIndication of lamp monitor Clean the air filter Cleaning and replacement of air filterProcedure of cleaning Dismantle the air filterLamp When to replace the Lamp unitReplacing the lamp unit AfterLamp unit will be hot after it has been used Lamp unit replacement stepsRemove the two screws securing the fan unit Have a Phillips screwdriver ready ahead of timeCeiling Mount Bracket Safeguards Installation procedureNo image Power doesNot turn on Image is blurredSpecifications PT-D5700E PT-D5700EL PT-DW5100ERemote control Power source Length of power cord CabinetOutside dimensions Replacement lamp unitCompatible Signal List PAL-M/PAL60 PAL/PAL-N/SECAMDimensions Installation dimensions diagramFor business users in the European Union Trademark Acknowledgement