OPTION1 settings
OPTION1 |
| |
| COLOR MATCHING | OFF |
| COLOR CORRECTION | USER |
| CONTRAST MODE | NORMAL |
| AUTO SIGNAL | OFF |
| BACK COLOR | BLUE |
| STARTUP LOGO | OFF |
| SUB MEMORY LIST |
|
| DVI EDID | EDID2:PC |
| DVI SIGNAL LEVEL | |
| FUNC1 |
|
| OSD POSITION | 1 |
| OSD MEMORY | ON |
|
|
|
| MENU SELECT |
|
| CHANGE |
|
COLOR MATCHING
When multiple sets are used simultaneously, this projector allows the user to correct the difference of colours among the sets.
Press 
to select “COLOR MATCHING”.
Press 
to switch “COLOR MATCHING”.
The setting will change as follows each time is pressed.
OFF : Colour matching adjustment is not carried out.
3COLORS : It is possible to adjust the 3 colours of “R (Red)”, “G (Green)” and “B (Blue)” and “Wh (White)”*.
*When “3COLORS” is selected, only the brightness can be adjusted for “Wh”.
7COLORS : It is possible to adjust the 7 colours of “R (Red)”, “G (Green)”, “B (Blue)”, “Cy (Cyan)”, “Mg (Magenta)”, “Ye (Yellow)” and “Wh (White)”.
MEASURE : Refer to “Adjusting the colour matching using a colourimeter” on the right for details on these modes.
If “3COLORS” or “7COLORS” was selected in step 2.
Press the ENTER button.
The “COLOR MATCHING: 3COLORS” or “COLOR
MATCHING: 7COLORS” screen will be displayed.
Press 
to select “R”, “G”, “B” and “Wh”.
(“R”, “G”, “B”, “Cy”, “Mg”, “Ye” and “Wh” when selecting “7COLORS”.)
Press the ENTER button.
Press 
to adjust the values.
These values can be adjusted from 0 to 2048.
(If the default value of the colour is 2048, the value can be adjusted from 256 to 2048.)
Note | • The effects of correcting the adjustment colour |
When tuning the correction colour that is the same as the adjustment colour
:The brightness of the adjustment colour changes.
When tuning the correction colour RED
:RED is added to or reduced from the adjustment colour.
When tuning the correction colour GREEN
:GREEN is added to or reduced from the adjustment colour.
When tuning the correction colour BLUE
:BLUE is added to or reduced from the adjustment colour.
•This adjustment should be carried out by a person who is familiar with the projector or by a service person because a high level of skill is required to make successful adjustment.
•Pressing the DEFAULT button will restore the factory defaults for all items.
•When any setting other than “OFF” has been selected for “COLOR MATCHING”, “AI”, “COLOR CORRECTION” and “COLOR TEMP” settings are not adjustable.
•When “AUTO TESTPATTERN” is set to “ON”, the test pattern for adjusting the adjustment colour is automatically displayed.
Adjusting the colour matching using a colourimeter
The “R (Red)”, “G (Green)”, “B (Blue)”, “Cy (Cyan)”, “Mg (Magenta)”, “Ye (Yellow)” and “Wh (White)” colours can be changed to the desired hues using a colourimeter which is capable of measuring the chromaticity coordinates and luminance.
Inputting the current luminance and chromaticity coordinates
Press 
to select “COLOR MATCHING”.
Press 
to select “MEASURE”. 
Press the ENTER button.
The “COLOR MATCHING:MEASURE” screen will be displayed.
Press 
to select “MEASURED DATA”. 
Press the ENTER button.
The “MEASURED DATA” screen will be displayed.
Use the colourimeter to measure the luminance (Y) and chromaticity coordinates (x, y).
Press 
to select the colours, and
press 
to select their values.
ENGLISH
(Continued on the next page)
33